Activity Stream
-
Older Activity
-
Today, 08:27 PMDougW9876 replied to a thread Bath fan switch in New To RV'ing, Purchase Questions & General ConcernsGreat Idea. I found the switch at Lowe’s for less than 6 dollars, took me about 15 minutes to swap it out. Problem Solved.38 replies | 2344 view(s)
-
Today, 08:23 PMMine run 120s on trip last week in Florida.5 replies | 278 view(s)
-
Today, 08:19 PMTried two RV locks. First one arrived with literally no key locks. Returned. Second one was showing rust in two weeks. Returned. Went with this...5 replies | 198 view(s)
-
Today, 08:10 PMWhile poking around underneath the trailer I saw our LP port for the first time. It has what appears to be a ball valve (handle turns 90*) and it was...5 replies | 666 view(s)
-
Today, 08:02 PMWe typically start a travel day with pretty close to a normal breakfast. The biggest exception is that we normally make our own juice, but on travel...21 replies | 695 view(s)
-
Today, 08:00 PMYeah, I am thinking that might be the quicker and easier option. Thanks.7 replies | 131 view(s)
-
Today, 07:38 PMtrailrydr replied to a thread Rust prevention on rotors over winter? in Axles, Brakes, and SuspensionWouldnt sweat it..... They will clean on first usage if brakes are working properly?1 replies | 32 view(s)
-
Today, 07:01 PMYou mean if NB Canada said its so, it must be true. LOL21 replies | 695 view(s)
-
Today, 07:01 PMWhen I press hitch height...it does nothing...if I press it again it raises the rear jacks. It's the best I can get the ground control 3 work.... re...28 replies | 1211 view(s)
-
Today, 06:52 PMButcher replied to a thread 2022 260RD 12Volt LiFePO4/Solar/Inverter Install in Solar Systems and GeneratorsI know I am one of the few that think 'quoting' pollutes a thread way too much. I do not feel quoting is always necessary because many times it's...22 replies | 11796 view(s)
-
Today, 06:49 PMCheck out complete axles at etrailer. About $500 per axle complete with bearings, brakes ($1000). add in springs at about $72 per ($288). Add...7 replies | 131 view(s)
-
Today, 05:50 PMWow, look terrible on every side but the one facing the sun exposure. I'm assuming they will smooth off with some braking action. Do covers help...1 replies | 32 view(s)
-
Today, 05:34 PMHaven't ever used the pump. Seems to be working OK for now, I don't have any idea what's going on with it.4 replies | 124 view(s)
-
Today, 05:26 PMhuntindog replied to a thread is my GMC 3500HD diesel denali pkg SWR 4x4 enough to pull a 2016 GD Momentum 397TH? in Tow VehiclesA 397 needs a dually30 replies | 1849 view(s)
-
Today, 05:11 PMjeririgged223 replied to a thread is my GMC 3500HD diesel denali pkg SWR 4x4 enough to pull a 2016 GD Momentum 397TH? in Tow VehiclesIt's plenty of truck to tow / pull it but it more about the cargo capacity. You will want to attach the 5th wheel trailer to your truck and drive...30 replies | 1849 view(s)
-
Today, 05:10 PMThanks; that is very good to know.11 replies | 288 view(s)
-
Today, 04:09 PMRip off. Axle alignment should be around $400. New springs $250. Bearings, seals, etc, $100. Thrown in a wet bolt kit $150 New equalizer $130-$190...7 replies | 131 view(s)
-
Today, 03:59 PMThanks Howard, I appreciate that. I am going to just pay for the diagnostic, get it back and consider what to do. I am leaning towards DIY.7 replies | 131 view(s)
-
Today, 03:55 PMYou may be correct with the different model years having different settings. My buddy has a 2018 337RLS and I have a 2019 337RLS, his requires him to...28 replies | 1211 view(s)
-
Today, 03:53 PMTo the original question... If you unhook the truth with no weight on the hitch (meaning slight gap between trailer and hitch) you can hook back up...28 replies | 1211 view(s)
-
Today, 03:52 PMWell, if the axles aren't bent or damaged, I certainly wouldn't replace them. Definitely new springs, new Dexter EZ-Flex equalizers, new wetbots and...7 replies | 131 view(s)
-
Today, 03:37 PMThanks! 3,500lb axles I have not serviced them - my bad I know. The prices include parts and overhauling is replacing the worn springs,...7 replies | 131 view(s)
-
Today, 03:35 PMAnd FWIW, many who defend the 12V compressor fridges say they have been around in boats for quite some time. So not necessarily new tech.11 replies | 288 view(s)
-
Today, 03:31 PMThis is JMO, and I'm offering it for free, so it is worth all you paid for it. :) Does that price of $1,200 include parts? Such as bearings, brake...7 replies | 131 view(s)
-
Today, 03:21 PMtruckin-on replied to a thread Width of slide-out on 349M? Could you get a dinette in there? in General DiscussionGot my answer - asked a sales guy at the dealer I've been talking with - who has one on the lot. The slide width is only 9' 8", so assuming the two...1 replies | 94 view(s)
-
Today, 03:10 PMJust took my 2500RL trailer to a truck axle place because I was getting very uneven tire wear. They found the bearings are worn, the alignment is...7 replies | 131 view(s)
-
Today, 03:00 PMIt’s all about managing the payload. Take trailer fully loaded gross weight and use 15% for tongue weight and you have worse case trailer payload. ...14 replies | 813 view(s)
-
Today, 02:42 PMWelcome to the forum, glad to have you with us. Let us know if anything comes up you could use a little help with, some very knowledgeable folks here.3 replies | 86 view(s)
Tire TPMS temps
Today, 08:23 PM in Tires