Activity Stream
-
Older Activity
-
Today, 01:30 AMDon’t believe everything you read on the internet. It’s up to the reader/viewer to decipher fiction from nonfiction. Coffee and a homemade sausage...23 replies | 767 view(s)
-
Today, 12:32 AMWell, I hate to say it, but you'll probably get another chance to replace them. Before I went with the Alcans, I'd typically find at least one...18 replies | 843 view(s)
-
Yesterday, 11:53 PMIf you thinking of replacing the axles upgrade to 4400 or even 5200 ones and select a spring one heavier than what you have. The bigger axles get you...9 replies | 184 view(s)
-
Yesterday, 11:51 PMLooking at DIY upgrade to 5,200lb axles however I am concerned the weight of the axles makes it too difficult to DIY. I saw on etrailer that they can...9 replies | 184 view(s)
-
Yesterday, 11:45 PMMtn Dew and healthy snacks like carrots and celery. Also strike up a conversation. Do you have a co-driver? if not and your feeling it STOP and take...23 replies | 767 view(s)
-
Yesterday, 11:36 PMpowerscol replied to a thread Beeping from Converter when operating slide out in Electrical System and WiringTake the battery to any auto parts store and have them do a load test. Cup of coffee its toast.6 replies | 278 view(s)
-
Yesterday, 11:31 PMpowerscol replied to a thread is my GMC 3500HD diesel denali pkg SWR 4x4 enough to pull a 2016 GD Momentum 397TH? in Tow VehiclesIn a word NO!!!!!!!!!!! The pin weight could be close to 4000 lbs (20% of GVW which is 20,000 lbs) You will also be exceeding the GVWR and possibly...32 replies | 1980 view(s)
-
Yesterday, 11:23 PMhttps://www.tractorsupply.com/tsc/catalog/bottle-jacks? I have a 12 and 6 ton Torine is a good brand - never had an issue. I have had one of these...2 replies | 60 view(s)
-
Yesterday, 11:11 PMI am just now on my way home from Hreen Vapley, AZ to Omaha. While in Green Valley, I had Happy Camper repack my wheel bearings. When they pulled the...10 replies | 617 view(s)
-
Yesterday, 10:49 PMSpartacus replied to a thread is my GMC 3500HD diesel denali pkg SWR 4x4 enough to pull a 2016 GD Momentum 397TH? in Tow VehiclesYeah, 6k is a bit much maybe he will come back and change that.32 replies | 1980 view(s)
-
Yesterday, 10:40 PMIt takes quite a bit of lifting height, so you need blocking to get the job done. Your GVWR is about 6 ton, and you are unlikely to need to lift half...2 replies | 60 view(s)
-
Yesterday, 09:51 PMI have a 2021 Grand Design Reflection 303 RLS and put MORryde Independent Suspension with hydraulic/electric brakes. I am trying to find how to raise...2 replies | 60 view(s)
-
Yesterday, 09:39 PMpowerscol started a thread Hub Savers - Thoughts on this new product in Axles, Brakes, and Suspensionhttps://thehubsaver.com/ I am attending a State Rally and getting a bearing repack done by https://performancetrailerbraking.com/ Folks seem to...0 replies | 24 view(s)
-
Yesterday, 09:23 PMDaytrepper replied to a thread Beeping from Converter when operating slide out in Electrical System and WiringDefinitely was the battery voltage alarm. I set it on a trickle charge for about 8 hours. Ran the slide out to get it cleaned out and prep...6 replies | 278 view(s)
-
Yesterday, 09:17 PMI am interested in getting into 3D printing. Chances are we will be taking it on the road. Anyone else have experience with them? What are some good...0 replies | 46 view(s)
-
Yesterday, 08:57 PMI found this thread when I was searching how to reinforce the hanger bracket. I don't have a GD RV. Yet. I have a 2006 Fleetwood Gearbox 220FB toy...399 replies | 190650 view(s)
-
Yesterday, 08:44 PMHaven’t been there. How is it? Rich14 replies | 614 view(s)
-
Yesterday, 08:27 PMDougW9876 replied to a thread Bath fan switch in New To RV'ing, Purchase Questions & General ConcernsGreat Idea. I found the switch at Lowe’s for less than 6 dollars, took me about 15 minutes to swap it out. Problem Solved.38 replies | 2379 view(s)
-
Yesterday, 08:23 PMMine run 120s on trip last week in Florida.5 replies | 286 view(s)
-
Yesterday, 08:19 PMTried two RV locks. First one arrived with literally no key locks. Returned. Second one was showing rust in two weeks. Returned. Went with this...5 replies | 214 view(s)
-
Yesterday, 08:10 PMWhile poking around underneath the trailer I saw our LP port for the first time. It has what appears to be a ball valve (handle turns 90*) and it was...5 replies | 691 view(s)
-
Yesterday, 08:02 PMWe typically start a travel day with pretty close to a normal breakfast. The biggest exception is that we normally make our own juice, but on travel...23 replies | 767 view(s)
-
Yesterday, 08:00 PMYeah, I am thinking that might be the quicker and easier option. Thanks.9 replies | 184 view(s)
-
Yesterday, 07:38 PMtrailrydr replied to a thread Rust prevention on rotors over winter? in Axles, Brakes, and SuspensionWouldnt sweat it..... They will clean on first usage if brakes are working properly?1 replies | 49 view(s)
-
Yesterday, 07:01 PMYou mean if NB Canada said its so, it must be true. LOL23 replies | 767 view(s)
-
Yesterday, 07:01 PMWhen I press hitch height...it does nothing...if I press it again it raises the rear jacks. It's the best I can get the ground control 3 work.... re...28 replies | 1298 view(s)
-
Yesterday, 06:52 PMButcher replied to a thread 2022 260RD 12Volt LiFePO4/Solar/Inverter Install in Solar Systems and GeneratorsI know I am one of the few that think 'quoting' pollutes a thread way too much. I do not feel quoting is always necessary because many times it's...22 replies | 11809 view(s)
-
Yesterday, 06:49 PMCheck out complete axles at etrailer. About $500 per axle complete with bearings, brakes ($1000). add in springs at about $72 per ($288). Add...9 replies | 184 view(s)
Do you consume anything on long...
Today, 01:30 AM in General Discussion