User Tag List
Likes: 0
Results 11 to 20 of 45
-
07-23-2018, 10:55 AM #11
- Join Date
- Aug 2017
- Location
- Crosslake, MN
- Posts
- 397
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
2018 Reflection 28BH
Andersen Ultimate Hitch ISR Version
Predator 3500W Inverter Generator
2017 Ram 3500 Mega cab SRW w/6.4L Hemi, Ramboxes, Active Air Rear Suspension
2017 Aluma 8214HS
2015 Lund Crossover 1775 XS
-
07-23-2018, 10:59 AM #12
- Join Date
- Jan 2018
- Location
- Sarasota Fl
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks guys for the input.
Yes I also think the legs are overly extended. I don’t have any more blocks with me at this time. No doubt, next time- more! The rig is certainly rocking too much with legs flexing...
That said would higher blocking assist with leveling issue?
The ball on the Anderson hitch is up high however next pin hole down caused an issue with clearances.
And separate note... it pulls just fine and really like the Anderson configuration. Very easy to install and remove.
-
07-23-2018, 11:03 AM #13
- Join Date
- Nov 2016
- Location
- Florida
- Posts
- 2,822
- Mentioned
- 30 Post(s)
- Tagged
- 0 Thread(s)
Notice from Jason’s picture and mine we both have our coupler in the “reverse” position.
Jerry & Linda
Emma & Abby our Mini Golden Doodles & JR our Amazon Parrot
2017 Reflection 337RLS, Build Date 01/2017, Titan Disk Brakes, Goodyear G614s 235/85/16 G Rated tires
2022 F-450 King Ranch Ultimate, 4,868 lb Payload, Bedrug Bedliner, Andersen Ultimate II Aluminum 5th wheel hitch
http://visitedstatesmap.com/image/FLGANCSCsm.jpg
-
07-23-2018, 11:14 AM #14
- Join Date
- Jun 2014
- Location
- South Dakota
- Posts
- 3,371
- Blog Entries
- 1
- Mentioned
- 22 Post(s)
- Tagged
- 0 Thread(s)
Dan & Carol
2014 303RLS Reflection #185 (10/2013 build)
2012 Silverado LTZ Crew Duramax 2500HD
2700/16K Pullrite Superglide
-
07-23-2018, 11:21 AM #15
- Join Date
- Aug 2017
- Location
- Crosslake, MN
- Posts
- 397
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
I just got back from a trip to a campground that had very tight sites and I had to jackknife the truck and trailer to get into the site. I'm sure I was at a 90 degree turn and all I could think about was the front cap smashing into the cab. My wife said there was still 5-6 inches of clearance between the camper and cab. The reason I mention this is because it works while having the coupler reversed. Reversing the coupler obviously moves the front cap of the camper closer to the cab but gives you better tailgate and siderail clearance. I needed that siderail clearance because my truck bed is only 51" wide due to Ramboxes.
2018 Reflection 28BH
Andersen Ultimate Hitch ISR Version
Predator 3500W Inverter Generator
2017 Ram 3500 Mega cab SRW w/6.4L Hemi, Ramboxes, Active Air Rear Suspension
2017 Aluma 8214HS
2015 Lund Crossover 1775 XS
-
07-23-2018, 11:31 AM #16
- Join Date
- Jan 2018
- Location
- Sarasota Fl
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Dan, thanks for the manual reference. I do not have the auto leveling or ground control set up. Just electric motor that controls the 2 front landing legs. And, i cannot find in my manual stating the pin hole allowance! I see it in the reference you made. Regardless I know it’s too high, that makes sense.
-
07-23-2018, 11:40 AM #17
- Join Date
- Jan 2018
- Location
- Sarasota Fl
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Now I see the page concerning pin allowance however since it was referencing the lcd screen which I don’t have... I skipped over it....
-
07-23-2018, 11:43 AM #18
- Join Date
- Jan 2018
- Location
- Sarasota Fl
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
07-23-2018, 11:47 AM #19
- Join Date
- Jan 2018
- Location
- Sarasota Fl
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
07-23-2018, 11:55 AM #20
Rob (Three Gs) - The powered section of your landing gear has something like 18" of travel. It takes a while with the drop section only 6 holes out . . . but, it will get there .
Not really part of this discussion, but I use different drop heights all the time, usually between 5 and 10 holes showing. This is to spread the wear on the drive track to more than the same few teeth under load on a level surface, all the time.
(another) RobCate & Rob
2015 Reflection 303RLS
2022 367BHS Reflection 5th wheel ...
Today, 07:31 AM in Trailers For Sale & Wanted