User Tag List
Likes: 0
Results 1 to 8 of 8
Thread: 295RL slide out problems
-
05-27-2019, 12:30 PM #1
- Join Date
- Mar 2019
- Posts
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
295RL slide out problems
I have an intermittent issue with my 295RL. Sometimes the dinette slide-out works and sometimes it doesn't. It is still under warranty, but I was trying to get the slide out in so I popped the switches and was just going to swap them. But when I was in the process something happened and I have no idea how the wiring is supposed to go. Anyone have a schamtic or how the switches wire up? Have to get it together right to bring it in.
Thank you.
-
05-27-2019, 12:58 PM #2
- Join Date
- Jun 2018
- Posts
- 2,356
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
I am just going to take a guess here....
The switch has on the back a place to plug a wire on the top, middle and bottom, if you have a meter you could test which one is the hot , that will go into the middle, should be black. The other 2 , one would go to the top and other to the bottom. To choose the right one will be trial and error to match the movement of the slide, extend, retract.
Not very helpful I know but maybe just enough.
If you could post a picture that would help me.
Brian
-
05-27-2019, 01:11 PM #3
- Join Date
- Mar 2019
- Posts
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
If it was only three wires I could probably figure it out, but it has four. One off to the side which I am assuming is the hot and three on the other side.
-
05-27-2019, 01:22 PM #4
- Join Date
- Jun 2018
- Posts
- 2,356
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
Do you have black wires or white wires?
Brian
-
05-27-2019, 01:30 PM #5
- Join Date
- Jun 2018
- Posts
- 2,356
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
Went out and took some pics. I have three slides.
Brian
-
05-27-2019, 01:32 PM #6
- Join Date
- Jun 2018
- Posts
- 2,356
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
Here are 2 more.
Brian
-
05-27-2019, 02:40 PM #7
- Join Date
- Mar 2019
- Posts
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thank you for the pictures, I'll try to figure it out tomorrow with the help of them.
-
05-27-2019, 10:03 PM #8
- Join Date
- Mar 2017
- Location
- Pearland, TX
- Posts
- 1,709
- Mentioned
- 15 Post(s)
- Tagged
- 0 Thread(s)
Mine are like this, probably other rigs will be a bit different.
Slide 1
-12V = White, +12V = White/Black
Motor- White, Motor+ White/Black
Slide 2
-12V = White, +12V =White/Red
Motor- White, Motor+ White/Red
Slide 3
-12V = White, +12V = White/Gray
Motor- White, Motor+ White/Gray
So my switch wires on Top & Bottom are -12, +12. Middle is Motor -, +
My switch is like the JR Products 12395.
- Gene
Kim & Gene
2015 Reflection 317RST
2017 Ram 3500 CC LB 4x2 6.7 CTD AISIN 3.73 DRW Auto Level Rear Air, BD3, Prodigy P3, Aux Tank
No power to RV
Today, 07:41 PM in Exterior