User Tag List
Results 31 to 36 of 36
-
04-17-2020, 10:58 PM #31
2017 Reflection 26RL "Mili"
2016 Ford F250 Extended Cab Gas Engine "Buck" (the truck)
-
04-19-2020, 11:19 AM #32
- Join Date
- Feb 2017
- Location
- Ontario, Ohio
- Posts
- 485
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Joe & Dee
Ontario, Ohio
2018 Chevy 3500HD LTZ Duramax Crew Cab SRW Short Bed Payload 3523#
2019 Reflection 337RLS bought February 2019 Dry Pin Weight = 2,320#, UVW = 11,100#
Hitch - PullRite Super Glide 2700 - 16K
Bed Cover - Roll-N-Lock
TPMS - Tire Tracker TT-500 (non flow thru)
Rear Observation Camera - Rear View Safety model RVS-155W-FB (2400-2500MHZ)
2017 303RLS bought April 2017 / Traded February 2019
Map represents States visited with our 303RLS /337RLS
-
04-19-2020, 11:37 AM #33
Well, he bought a small plastic electronics box that fit the touch pad, turned off the power, removed the pad from the wall, cut the cable near the pad, spliced in about 6' of new cable (soldering and using shrink tubing), mounted the pad into the box and voila..
This is the wall after he took the pad off
2017 Reflection 26RL "Mili"
2016 Ford F250 Extended Cab Gas Engine "Buck" (the truck)
-
05-07-2020, 02:09 PM #34
- Join Date
- Jan 2020
- Location
- TN
- Posts
- 163
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
Hi folks!
I just tried the auto-reconnect feature after unhooking from the truck in my driveway and I get the "Feature Disabled" message.
Here's some data. When I raised the front end of the camper high enough to pull the truck out from under the Andersen ball funnel, the distance from the funnel's bottom edge to the concrete is 56.5". When I tired the Auto-level at this point, an "Excessive Angle" error came up. I then dropped the front end down to 54.75" and tried it again and the Auto-level worked.
I tuned off the Lippert GC 3.0 System, waited about three seconds and turned it back on. When I then tried the Auto-Reconnect I received the "Feature Disabled" message, so I tried the left-right button combination and the same message popped up.
What am I doing wrong?
Thanks.2020 Grand Design 230 RL
2019 Ford F-250 6.7L Diesel
-
11-01-2020, 04:44 AM #35
- Join Date
- Oct 2020
- Location
- Virginia....up in the northern neck
- Posts
- 98
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Auto reconnect will only work if autolevel works and power was not lost to the controller. If you were not able to use auto level, you will not be able to use auto reconnect.
2021 Reflection 303rls
2019 ram 2500 cc 4x4 6.4l gas short bed2021 GD Reflection 303rls
2019 ram 2500 Crew Cab tradesman 4x4
Autoslider 5th wheel hitch.
-
11-01-2020, 04:00 PM #36
- Join Date
- Feb 2017
- Location
- On the road, retired
- Posts
- 428
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
Or like with mine, a new 2020 solitude, auto level works fine. But auto reconnect has not worked since about after the 4th or 5th time trying to use it. The only way we can retract our 6 point hydraulic landing gear is to press retract all, even manual mode will only raise the rear right side. Then we can raise the front gear to the reconnect height. Even though grand design says they will warranty it, we are on a year long road trip, and we have not found a mobile mechanic that can fix it in the time frame that we're in there area. This rig is falling apart.
Washing machine on/off valve
Today, 04:24 PM in Plumbing and Water Systems