User Tag List
Thanks: 0
Likes: 0
Results 1 to 9 of 9
Thread: sticky brakes
-
03-05-2015, 08:04 PM #1scottyGuest
sticky brakes
Hi all
Just got back from our 4th 200 mile shakedown trip around the block by way of the Oregon coast with our new Solitude 379 FL and it has
preformed flawlessly until about 10 miles from home when the drivers side of the trailers front brake started sticking and smoking the tires.
I have not looked at it yet and was wondering if this is something i can fix my self. I would rather not have to make the 60 mile trip to the
dealer if it is just an adjuster nut that can be turned in a bit. Also does anyone know if the brakes are self adjusting and will set themselves by just
backing up and applying the brake. Any input on this would be greatly appreciated.
Thanks Scotty
-
03-05-2015, 08:34 PM #2
Scotty - I believe the brakes on the Solitudes are the same as the Reflections in that they are NOT self adjusting. They are pretty simple to adjust though. Here's a video from Lippert on how to do it:
https://www.youtube.com/watch?v=ih1pLKHELIs
But I'd be suspicious that it's not an adjustment issue. It could be you have self adjusting brakes, and they self adjusted a little too tightly. It could also be that you have debris in the brake drum and it's causing an issue. Finally, I'd recheck you brake controller to make sure the adjustment is correct.
-
03-05-2015, 11:19 PM #3scottyGuest
thanks Jim for the web page very helpful.
I did check the controller and could feel the difference on all the other brake when turned down
but the problem one still would lockup i will also check for debris that could happen, we did go down some gravel
roads on our trip.
thank you
-
03-06-2015, 02:28 PM #4Steve and LynneGuest
Hello Scotty!
Want to help- MANY years of auto/truck/trailer experience, way back when 4 wheel drum brakes were standard (same as our fifth wheels). Jack up and jackstand the one wheel, pull tire. Pull center cap, you will see a cotter pin through center spindle. Remove it, unthread nut, jostle hub and drum assembly but be sure to catch the washer and bearing. Slide drum off slowly and evenly. Now- is the seal on the inner hub keeping grease in the bearing or is it all over the brake shoes? If not, good! (I had all 4 seals leaking a bunch of grease). Look to see if all the springs and hardware look in the proper place. If you are not sure, disassemble the other wheel on that side (after jacking up and installing a jackstand). There should be Youtube videos. Have new cotter pins available, tighten nut very snug, repeat, and back off as little as possible so nut is loose by less than 1/6 of a turn. This may motivate you to seek professional tech help. I am very hands on, want to minimize waiting time and do have confidence in my thoroughness. You may be able to use your leveling system to raise axles, just use jackstands for safety, recommend under leaf spring and axle junction.
-
03-06-2015, 02:30 PM #5Steve and LynneGuest
If you tackle it yourself, get cotter pins before disassembly. 1/8" x 1-1/2" work OK, a little small.
-
03-06-2015, 03:15 PM #6
My Reflection had leaking grease seals also. I replaced all the seals and brakes. When I replaced the brakes, I installed complete assemblies (backing plate, magnets, shoes) with self adjusting brakes. Self adjusting brakes make a world of difference in stopping power. Here's a picture of one of my leaking seals. You can see grease on the inside of the hub in this picture.
A tell-tale that I had leaking seals was spots of grease on the inside of the rims.
-
03-06-2015, 07:55 PM #7scottyGuest
Thanks guys
I am also a hands on guy and have done electric brake many times on my snowmobile trailers, just did not know if there was something new with this
new trailer. I will get started on it this weekend and will checkout everything seals, mag, shoes. I am also going to change too self adjusting brakes if they
are not. i agree with Jim i think self adjusting brakes are better and have better stopping power. I had them on our Montana and never had one problem with
them.
thanks guys for all your input
-
03-08-2015, 01:26 PM #8Steve and LynneGuest
I am glad you are hands on and experienced. I had Jim's grease problem times four! The self-adjusting idea is going to happen fairly soon for me too. We can't have too much braking- with a proper controller of course. Please let us know your findings.
-
03-09-2015, 07:09 PM #9scottyGuest
Hay guys
seems just a simple adjustment is all it took, everything seem to be working good the brakes look brand new and i will
continue to use them until it is time for new ones or if i have problems down the road. I will be doing self adjusting ones
in the future but for know i will run the current ones. The seals and bearings all look new and seem to be doing there job
as far as i could tell just the one brake was setup to close it only took 3 turns to lock up the brake so i adjusted them
all down to 6 and re set the gain on the controller a little less. I live on a very steep 4 mile down hill so trying them out was easy
and they worked like they should.
thanks for all your input, that is one of the thing that is so cool about this forum there are so many knowledgeable people willing
to help.
Similar Threads
-
this should be a sticky for all with the single sink island!!
By NachoFirme in forum General DiscussionReplies: 5Last Post: 11-19-2015, 07:50 PM
Slide actuator failure on 2021...
Today, 02:45 PM in General Discussion