User Tag List
Thanks: 0
Likes: 0
Results 1 to 10 of 21
Thread: Installing a rear hitch
-
12-14-2014, 09:56 AM #1janmacleanGuest
Installing a rear hitch
I have a 2014 303rl and would like to install a hitch at the rear, has anyone done that? I know the new one's have it done and when I looked at one it was a bolt on. Since I have a bumper there is no way to bolt one on.
-
12-15-2014, 10:26 AM #2
- Join Date
- Jul 2014
- Location
- Woodland, California
- Posts
- 93
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
We have a 2015 303rls with the standard 4" bumper. I purchased a bolt on receiver from Camping World. Use it for our bike carrier. No problems for this application.
"It's the journey that matters-not the destination."
Ken & Suzi
2013 2500HD Silvarado Duramax
2015 303RLS
-
12-15-2014, 01:04 PM #3
- Join Date
- Sep 2013
- Location
- PA
- Posts
- 4,453
- Mentioned
- 229 Post(s)
- Tagged
- 0 Thread(s)
Go to a certified welder and have them install a regular 2" receiver hitch under the bumper, mounted to the frame.
The clamp on receivers will eventually twist the bumper off. The 4" steel bumpers are only rated for 150 Lbs of load.Steve- Inventory Manager at Tom Schaeffer's RV, Shoemakersville, PA www.tomschaeffers.com
[email protected]
2011 RAM 3500 SRW Outdoorsman Edition 4X4, 6.7 Cummins--TWEAKED!
2021 Reflection 310RLS
-
12-15-2014, 06:46 PM #4
- Join Date
- Jan 2014
- Location
- Northfield Center, Ohio
- Posts
- 505
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
It took me some time and money, but I ran two pieces of channel steel from both frame channels, the rearmost bolted through the four inch bumper. To the channel steel, I welded three 2" box pieces. I also obtained two aluminum wheelchair ramp/transport platforms and bolted them together. The end result is a platform about 30" in width, 8' long, with a ramp on it. It should be able to hold somewhere around 500 lbs.
If I was one of these high tech guys, I would send a picture.
Gord and Janet Fuchs
Presently at Fairview-Riverside, LA.
-
12-16-2014, 08:29 AM #5
I may be wrong, but doesn't welding to the frame void the frame warranty?
Jim
-
12-16-2014, 11:41 AM #6
- Join Date
- Jun 2014
- Location
- South Dakota
- Posts
- 3,371
- Blog Entries
- 1
- Mentioned
- 22 Post(s)
- Tagged
- 0 Thread(s)
Jim--you are correct. Lippert shared with me in a phone conversation a few months ago that the warranty would be void with adding a welded or bolted hitch unless I brought our RV to their facility and they welded it on. Pragmatically in our situation it does not make a difference since as second owners, the Lippert frame warranty unlike the GDRV basic 1 year warranty is not transferable.
DanDan & Carol
2014 303RLS Reflection #185 (10/2013 build)
2012 Silverado LTZ Crew Duramax 2500HD
2700/16K Pullrite Superglide
-
12-16-2014, 09:16 PM #7
- Join Date
- Jan 2014
- Location
- Northfield Center, Ohio
- Posts
- 505
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I made that decision, based on the fact that Lippert, in my opinion, does not offer a significant warranty anyway.
Gord Fuchs
-
12-18-2014, 02:38 PM #8
- Join Date
- Jun 2014
- Location
- Siloam Springs, Ar
- Posts
- 242
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
According to Micah at GD mods done to the frame only void the warranty if the mod was the cause of possible failures. I would be cautious of adding anything that would diminish ground clearance at the rear cause if you are towing any at all nose high that makes the rear drop drastically.
2014 Ram 2500 W / 6.7L diesel
2014 303 RLS
-
12-18-2014, 05:00 PM #9
- Join Date
- May 2014
- Location
- NW AL/NE GA Mountains
- Posts
- 2,083
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
You could also get a bolt on receiver hitch at Northern Tool and maybe Harbor Freight. I'd just be very careful to what you do with that hitch. Bicycles is about all I'd want to put back there unless substantial beefing up to the lightweight 4" square tubing and reinforcing the frame. Frames on most 5th wheel and travel trailers are notoriously lightweight.
-
12-18-2014, 06:01 PM #10ALLAIN MOTORSPORTSGuest
I have a 323bhs and welded a hitch to the rear of mine to tow my 20ft 5000lb boat. If done correctly for what ever it is you are wanting to tow it should not cause any failures. I put 2 2x2 thick wall tubing in between the I beams space 12 inches apart and 2 4x4 thick wall under the frame which dropped the receiver tube even with the bottom of the bumper. Then used angle on the top 2 2x2 that dropped down 3 inches past the 4x4 and ran the receiver tube through both pieces of angle and welded it all up. This is overkill for a bike rack but I wanted to be able to tow anything from my atv's boat or bikes.
Similar Threads
-
Installing Propride Hitch on 2670MK
By Dale G in forum General DiscussionReplies: 24Last Post: 06-08-2018, 08:19 PM -
Installing PullRite SuperRails in F350 -- anyone done it?
By pg_rider in forum Mods and DIYReplies: 9Last Post: 07-06-2015, 07:52 PM -
Installing a Progressive Industries EMSHW50C Surge Protector
By Phydeauxman in forum Electrical System and WiringReplies: 2Last Post: 08-12-2014, 06:16 AM -
Installing a Progressive Industries EMSHW50C Surge Protector
By Phydeauxman in forum ExteriorReplies: 1Last Post: 08-08-2014, 10:06 AM -
Installing additional window
By remdenver in forum General Tech TopicsReplies: 2Last Post: 07-01-2014, 04:01 PM
Channging Battery Type?
Today, 01:22 AM in Electrical System and Wiring