User Tag List
Results 21 to 30 of 39
-
05-14-2020, 04:42 AM #21
- Join Date
- Dec 2019
- Location
- Macedon, New York
- Posts
- 153
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
I also own a 2020 GM and they are currently working on a problem they have with their software. I can tell you though, This came from another person with the same problem. The system is basically not recognizing the trailers.
temporary fix that was shared with me was, Hook the trailer up shut the truck off for a few minutes and plug the unit in with the truck not running. It works.
-
05-14-2020, 08:21 AM #22
- Join Date
- Feb 2020
- Location
- Bend, OR
- Posts
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yes, I saw your thread last week describing a similar problem. I tried the sequence of delays at startup which someone had suggested there, and which apparently works for you. It didn't correct my problem. It would be interesting to know what brake system is on your trailer; electromagnetic vs electric-over-hydraulic, and if the latter, which brake actuator, and whether or not there is an EOH adapter.
I'm glad that the temporary fix you mention is working for you and some others!Don
2021 Solitude 310GK
2020 Silverado 3500HD/CC/SB/SRW
-
05-16-2020, 09:21 AM #23
- Join Date
- May 2017
- Location
- NorCal
- Posts
- 10
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I had the same problem with my 2016 F350. Talked to Bill many times but didn’t get it fixed. Tried the Fix Bill told me about, like you, no change. Took the truck to Ford, they checked it out, the EOH setting wasn’t any different than the std setting. So Ford says all good but it’s not. Spent $99 on a new Ford controller, problem gone.
-
05-16-2020, 10:12 AM #24
- Join Date
- Mar 2019
- Location
- Saint James NY ( Long Island)
- Posts
- 135
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I am glad to hear that. I'm assuming you are stuck at home as we are right now.
Today I installed my Ford/Chevy Adapter for the BrakeRite controller. Initially it was still making the pulsing noise but after actuating the brakes a few times it went away. It now is quiet when connected to my running 2019 F350.
I have not heard what a properly installed BrakeRite pump sounds like. I have not taken the trailer on the road to test it except for actuating the brakes in my driveway. It seamed to stop quickly. However, I am concerned that it sounds like it takes the pump a second or two to build up pressure. Attached is a video of what mine sounds like. Is this normal?
Best regards, Lou & Diane Cetrangelo, Saint James, NY
2019 Ford F350 Lariat | Dually | Diesel | 4x4 | Super Cab | 8' Bed | B&W Goose Ball
2020 Solitude 310GK | Reese 20k Goosebox |1,550 Watts of Solar | Victron 3k Mutiplus II | 3 SOK 206 AH Batteries | Disk Brakes | MorRide IS
-
05-16-2020, 02:26 PM #25
- Join Date
- Feb 2020
- Location
- Bend, OR
- Posts
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have read that there is some braking delay with EOH brakes, which I assume is just the time it takes for the pump to ramp up the hydraulic pressure. I believe if you have some air in your brake lines, that could also effect the braking time, but I honestly don't know what the BrakeRite pump should sound like, either.
On your F350, do you have the choice to set your brake controller for electromagnetic vs EOH? If so, are you using the EOH setting? Were you pressing the brake pedal or engaging the brake controller slide switch when you made the recording?Don
2021 Solitude 310GK
2020 Silverado 3500HD/CC/SB/SRW
-
05-16-2020, 03:02 PM #26
- Join Date
- Mar 2019
- Location
- Saint James NY ( Long Island)
- Posts
- 135
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I do have a choice and it is currently set for EOH. I had it set for electric and it seams to work the same way.
I had my wife squeeze the brake controller with the engine running.
I sent the video to Bill at Stop Your Trailer. He just called me back. He said the ramp up to full power and then it idles back a bit sounded normal. He was concerned about the plusing after that.
He had me pull the breakaway pin with out the truck connected. There was no plusing then. Its something that the truck is doing. He is going to check with the engineers and get back to me.
-
06-02-2020, 04:49 PM #27
- Join Date
- Feb 2020
- Location
- Bend, OR
- Posts
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Well, after a painfully long delay in getting an Hydrastar HBA-CAM EOH adapter (Bend Trailers is NOT on my recommended list of suppliers!), I was able to install the adapter this morning and it solved my incompatibility issue between the 2020 GM ITBC and the Dexter EOH actuator! Time will tell if it's a reliable solution, but for now it's working.
So I immediately pulled the trailer to the tire shop to have my GM supplied TPMS sensors installed, and of course, they are incompatible. Groan... But I was able to find a solution to that in the forums, so hopefully that's an insignificant hiccup compared to the brakes. Thanks, offtohavasu!Don
2021 Solitude 310GK
2020 Silverado 3500HD/CC/SB/SRW
-
06-26-2020, 10:08 AM #28
- Join Date
- Jun 2020
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks Don for the information. I am currently fighting the same issue with my 2019 Silverado and the Dexter 1600 actuator.
Have you tested the fix? I tried the dexter k58-011-00 which did not work.
Thanks for any information
email:[email protected]
-
06-28-2020, 08:09 AM #29
- Join Date
- Feb 2020
- Location
- Bend, OR
- Posts
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
06-28-2020, 05:22 PM #30
- Join Date
- Jun 2020
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I'll be installing it in the next couple of days. New 5er and can't get on the road. Take care and thanks
Extending 381m garage?
Today, 10:06 PM in General Discussion