User Tag List
Likes: 0
Results 1 to 5 of 5
Thread: Red blinking light
-
05-30-2020, 04:58 PM #1
- Join Date
- May 2020
- Posts
- 16
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Red blinking light
Hello....
2017 Reflection Fifth Wheel 29RS, new to me, leveled for the first time... auto level said success but i checked it with two large construction levels while on concrete drive.. it was not level, so used manual mode, and raised the nose. When I got it level, i got a red blinking light at the bottom of the panel near the REAR button. It will not go away unless i auto level again.. I cannot calibrate LEVEL either.... I have watched endless videos, googled and read manuals.. nothing tells me how to fix this. Reached out to Lippert Cust Serv, but nothing yet. I dont want to just ignore the blinking light and i would like to teach it what is level, but cant get past this step.
I assume they are electric jacks but how do i know? also, if i get the nose too high with the manual depressing of FRONT button, how do i then lower the nose?
Thanks for your support and help!
Ursa Major (very new-bie)
[email protected][FONT=Book Antiqua][COLOR="#000080"]Ursa Major
2017 Grand Design Reflection Fifth Wheel 29RS
-
05-31-2020, 10:09 AM #2
- Join Date
- Jun 2019
- Location
- Vancouver, WA
- Posts
- 273
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
https://www.google.com/url?sa=t&rct=...8tMy12t7kCHrMT
Sound like you need reset the system. Hope lippert contacts you soon.Bob and Cheryl, Puka the doodle
2018 Ram 2500 Crew,Diesel,4x4
2016 Reflection 27RL
2012 Palomino 6.5 camper
-
05-31-2020, 11:25 AM #3
- Join Date
- Jul 2014
- Location
- Wherever...
- Posts
- 9,119
- Mentioned
- 191 Post(s)
- Tagged
- 0 Thread(s)
Have you tried this procedure for the Ground Control 3.0?
Zero Point Calibration
The “Zero Point” is the programmed point that the trailer will return to each time the Auto Level feature is used.
Note: Prior to starting this procedure, double check all connections on the controller, jacks, and touch pad.
1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center of the trailer and leveling it both front to back and then side to side. (See “Basic Jack Operation” for instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3. With the touch pad off, press and release the “FRONT” button five (5) times and then press and release the “REAR” button five (5) times.
4. The touch pad will flash and beep and the display will read “ZERO POINT CALIBRATION ENTER to set, Power to Exit”.
5. To set the current position as the zero point, press the “ENTER” button.
6. LCD display will read “Zero point stability check”.
7. LCD display will read “Zero point set successfully” once process is complete.
8. The system will set this point as its level state and the touch pad will turn off.
Rob
EDIT: the Lippert procedure for the Level Up hydraulic system on our Solitude says "five times" when in fact some models require seven (7) times. I don't know if this might be true for the Ground Control 3.0 system, as well.Last edited by Second Chance; 05-31-2020 at 07:30 PM.
U.S. Army Retired
2012 F350 DRW CC LB Lariat PS 6.7
2020 Solitude 310GK-R, MORryde IS, disc brakes,
Sailun LRG tires, solar, DP windows, W/D
(Previously in a Reflection 337RLS)
Full time since 08/2015
-
06-02-2020, 11:12 AM #4
-
06-06-2020, 12:43 AM #5
- Join Date
- Sep 2019
- Location
- Pilot (Zebulon), NC
- Posts
- 383
- Mentioned
- 5 Post(s)
- Tagged
- 0 Thread(s)
310GK Bounce When Towing
Today, 11:04 PM in Fifth Wheel Hitching Topics