User Tag List
![Thanks](https://www.mygrandrv.com/forum/dbtech/thanks/images/thanks.png)
Results 21 to 30 of 39
Thread: GM Trailer Camera
-
02-23-2022, 01:57 PM #21
- Join Date
- Jan 2022
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
GREAT POST!!!
Im going to be doing the same mounting, and was wondering how to make sure I hit structure.
Thanks for posting!!!Aimlessly Wondering the USA
Andy and Teri
2022 GMC Denali 3500 CCSB 4x4 SRW DURAMAX!
2021 Reflection 337 RLS
-
02-23-2022, 04:19 PM #22
- Join Date
- Aug 2020
- Location
- Tulsa
- Posts
- 5
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I'm in the middle of installing mine and will be routing under the trailer in flex conduit to add some protection. You can take the camera housing apart and it will fit a 1/2" conduit. I just used conduit hangers using the coroplast screws down the edge of the frame. I'm essentially following the same as another 22MLE owner has done and fabricating a mount on aluminum bars that extends from the spare tire mount on the back bumper to avoid any drilling of the wall.
2021 Imagine XLS 22MLE
2022 GMC Sierra 2500 Denali
-
02-23-2022, 04:35 PM #23
- Join Date
- Jan 2021
- Location
- The Thumb of Michigan
- Posts
- 728
- Mentioned
- 11 Post(s)
- Tagged
- 0 Thread(s)
Regarding hitting an aluminum frame member when drilling. I hit aluminum on the upper screw only. This was not planned but made for a good mount. If I did not hit any aluminum, the mount would still be fine as the camera is light and IMHO the fiberglass wall material
Is sufficient for mounting.
Sent from my iPhone using Tapatalk2021 Reflection 312 BHTS, Silverado 2500 Duramax
-
03-11-2022, 09:59 PM #24
- Join Date
- Nov 2021
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
You guys are awesome and I’m going to copy this exact same setup. I have a 2022 reflection 31MB and a 2022 GMC Sierra Denali 3500HD.
Question, how are you guys feeding the underwire to the truck?
Ideally I would like the aux camera wire to come out where the power cable from Pinbox comes out, just not sure how you guys did it?
-
03-12-2022, 06:22 AM #25
- Join Date
- Jan 2021
- Location
- The Thumb of Michigan
- Posts
- 728
- Mentioned
- 11 Post(s)
- Tagged
- 0 Thread(s)
I just zip tied it to a few of those self adhesive zip tie anchors to the frame until I got to the propane line. Then zipped to that until I got to the 7 pin wire. Then zipped to that. Zip zip zip.
Sent from my iPhone using Tapatalk2021 Reflection 312 BHTS, Silverado 2500 Duramax
-
03-12-2022, 06:46 AM #26
- Join Date
- Nov 2021
- Posts
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks. However the propane line feeds into the propane side compartment, when then has a entrance way into the front compartment. From the front compartment where battery is to get from here to Pinbox I may have to pierce through and fish the wire. Is that what you did on your fifth wheel? Do you happen to have a pic?
-
03-12-2022, 08:17 AM #27
- Join Date
- Jan 2021
- Location
- The Thumb of Michigan
- Posts
- 728
- Mentioned
- 11 Post(s)
- Tagged
- 0 Thread(s)
Woops. My rig is a TT. Which is easier to wire since the 7 pin connector and camera connector are adjacent on the number of the truck. You will have to improvise a bit to get the camera wiring to the bumper of the truck. GM should put a camera connector in the bed as well as the bumper for fifth wheels. But, alas, not yet.
Sent from my iPhone using Tapatalk2021 Reflection 312 BHTS, Silverado 2500 Duramax
-
03-12-2022, 06:52 PM #28
- Join Date
- Feb 2017
- Location
- Ontario, Ohio
- Posts
- 485
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Not camera wire, but I fished a backup wire thru the pin box into the front compartment. From the front compartment I went thru a hole at the bottom rear street side into the inside of the coraplast. Then I started removing the screws 3-4 at a time tucking the wire as I went. At 67 this was 2 day affair and 2-3 beers a day. . . . . .
Joe & Dee
Ontario, Ohio
2018 Chevy 3500HD LTZ Duramax Crew Cab SRW Short Bed Payload 3523#
2019 Reflection 337RLS bought February 2019 Dry Pin Weight = 2,320#, UVW = 11,100#
Hitch - PullRite Super Glide 2700 - 16K
Bed Cover - Roll-N-Lock
TPMS - Tire Tracker TT-500 (non flow thru)
Rear Observation Camera - Rear View Safety model RVS-155W-FB (2400-2500MHZ)
2017 303RLS bought April 2017 / Traded February 2019
Map represents States visited with our 303RLS /337RLS
-
03-16-2022, 04:19 AM #29
- Join Date
- Dec 2018
- Location
- Guelph, Ontario
- Posts
- 27
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Found this post after I posted my question yesterday. I wonder if GM uses the same camera system as Ram? I suspect I will mount my system in same fashion.
-
11-20-2022, 11:29 AM #30
- Join Date
- May 2022
- Posts
- 47
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Slide actuator failure on 2021...
Today, 06:49 AM in Slide Systems