User Tag List
Thanks: 0
Likes: 0
Results 1 to 9 of 9
-
12-13-2021, 03:13 PM #1
- Join Date
- Dec 2021
- Posts
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Entertainment seats electrical system not functioning correctly
Two Entertainment seats, both both recline ok, heating elements ok, both vibrating ok, but one seat lights do not work. Plugged in OK at receptacle. Any ideas?
-
12-13-2021, 04:16 PM #2
- Join Date
- Apr 2018
- Location
- The Independant State of Alberta
- Posts
- 710
- Mentioned
- 8 Post(s)
- Tagged
- 0 Thread(s)
-
12-13-2021, 06:38 PM #3
- Join Date
- Dec 2021
- Posts
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Can you explain how to do the bulb replacement on these seats? New to this tech.
-
12-13-2021, 06:46 PM #4
- Join Date
- Apr 2018
- Location
- The Independant State of Alberta
- Posts
- 710
- Mentioned
- 8 Post(s)
- Tagged
- 0 Thread(s)
-
12-13-2021, 09:14 PM #5
-
12-13-2021, 11:39 PM #6
- Join Date
- Nov 2019
- Location
- S. E. PENNSYLVANIA
- Posts
- 947
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
Before you order a new strip light check the wiring from the strip light all the way to where it's plugged into the wiring harness. It's possible it has gotten pinched and cut or that it's come unplugged from the recliners wiring harness itself. Do you have cupholder lights as well, and do they work?Bill & Colleen ~ Schwenksville, Pa
2019 Reflection 337RLS
2006 GMC Sierra 3500 8.1L V-8
Firestone Ride-Rite Air Bags
Front Stabilizer Bar
Rear Anti Sway Bar
-
12-14-2021, 03:45 AM #7
- Join Date
- Dec 2021
- Posts
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
The cupholder on the same seat does not work as well. So, I need to figure out how to unfasten the entire seat(s) from the floor to get to the wiring underneath? That's not going to be easy.....
-
12-14-2021, 05:42 AM #8
- Join Date
- Nov 2019
- Location
- S. E. PENNSYLVANIA
- Posts
- 947
- Mentioned
- 16 Post(s)
- Tagged
- 0 Thread(s)
Since the cupholder is also not working it's probably not the LED lights that are bad. It could be the touch switch or the wiring harness itself. My recliners were never screwed down from the factory but it looks like the bar that runs across the front would be the only way to attach them to the floor. The recliners also lock together with two metal clips between each section, the recliner closest to the dining room table needs to be unscrewed and lifted up about 2" to unhook it from the center console. Next the center console can be lifted off (it's a separate pieces) to remove the second recliner if needed. When I had one recliner that wouldn't work I found it was the wiring components underneath had pulled apart from getting caught up in the folding mechanism.... it's all 12volt wiring after the power cord and everything plugged together with miniature banana jacks. If possible when you remove the screws could you post a picture of what they used and what length screws they are? I would like to screw mine down but don't want to get something that would penetrate the floor itself.Last edited by IBEW Sparky; 12-14-2021 at 05:47 AM.
Bill & Colleen ~ Schwenksville, Pa
2019 Reflection 337RLS
2006 GMC Sierra 3500 8.1L V-8
Firestone Ride-Rite Air Bags
Front Stabilizer Bar
Rear Anti Sway Bar
-
12-14-2021, 06:27 AM #9
- Join Date
- Apr 2018
- Location
- The Independant State of Alberta
- Posts
- 710
- Mentioned
- 8 Post(s)
- Tagged
- 0 Thread(s)
Plastic on Recliners?
Today, 12:48 PM in Interior