User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
-
05-20-2022, 07:35 AM #1
- Join Date
- Feb 2020
- Posts
- 45
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Steadyfast install on reflection 31mb question
I am going to install some steadyfast arms on my 2022 reflection 31mb. Has anybody done this and can help out with how you installed them with the gas lines on the drivers side? Did you move them or make it work without? Did you modify or move them to avoid the lines? Thanks in advance!
Andy
-
05-20-2022, 08:42 AM #2
- Join Date
- Nov 2017
- Location
- AZ
- Posts
- 251
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Hi Andy,
I put the Steadyfast system on my 28BH Not quite the same as a 31mb but pretty close. It took two of us about 6 hours going slow to make sure we did not mess something up. My gas lines are straight down my left frame rail so I did as little on that side as possible. I did not use the self taping bolts from the kit at most attach points. I used bolts, washers, lock washers and lock nuts everywhere I could to make sure it stayed where I put it.
I put them on this way:
Front end side to side - wing nut on the front left corner frame rail, attach to front right pad
Front end front to back - attach to front right pad and wing nut on the right frame rail about 5 feet back
Back end side to side - wing nut on the right side frame rail, attach to left rear pad.
Doing it this way I did not have any gas line issues as I only had one wing nut attachment point under the front left corner. I also put on Snap Pads during the install process. The Steadyfast system and the Snap Pads have been a great addition and I would do it again.
KevinKevin and Jennifer
2016 RAM 3500 Laramie Mega Cab CTD Aisin 4x4 SRW
2019 Reflection 28BH (Built 2/2019)
- 78" Theater Seat, Second AC, Dual Pane Windows
- Sailun 235/85 R16 Tires
Blue Ox Super Ride BXR7200 with a Demco Factory Prep Bracket 6099
-
05-20-2022, 09:24 AM #3
- Join Date
- Feb 2020
- Posts
- 45
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
-
05-20-2022, 10:55 AM #4
- Join Date
- Nov 2017
- Location
- AZ
- Posts
- 251
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Kevin and Jennifer
2016 RAM 3500 Laramie Mega Cab CTD Aisin 4x4 SRW
2019 Reflection 28BH (Built 2/2019)
- 78" Theater Seat, Second AC, Dual Pane Windows
- Sailun 235/85 R16 Tires
Blue Ox Super Ride BXR7200 with a Demco Factory Prep Bracket 6099
-
05-20-2022, 04:56 PM #5
- Join Date
- Feb 2020
- Posts
- 45
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
-
05-23-2022, 07:01 PM #6
- Join Date
- Feb 2020
- Posts
- 45
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
-
05-23-2022, 08:15 PM #7
- Join Date
- Nov 2017
- Location
- AZ
- Posts
- 251
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I did the drill and countersink method. Go slow and keep checking the bolt. I did not countersink very far because I was putting on Snap Pads.
Kevin and Jennifer
2016 RAM 3500 Laramie Mega Cab CTD Aisin 4x4 SRW
2019 Reflection 28BH (Built 2/2019)
- 78" Theater Seat, Second AC, Dual Pane Windows
- Sailun 235/85 R16 Tires
Blue Ox Super Ride BXR7200 with a Demco Factory Prep Bracket 6099
Check those tires!
Today, 03:33 PM in Tires