User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
Thread: Slide seals
-
07-04-2015, 04:03 PM #1
- Join Date
- Mar 2015
- Location
- CA
- Posts
- 693
- Blog Entries
- 1
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
-
07-04-2015, 07:37 PM #2
- Join Date
- Mar 2015
- Location
- Princeton, NJ USA
- Posts
- 416
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I checked mine after seeing this post earlier and no wear at all. I went through the entire rig, all 4 slides, right after I took delivery with slide lube.
2015 Reflection 323 BHS #589
Still working Electrical Engineer
Rob, Maureen, Dakota, Jacob and Murphy the Lab
JustinThyme (Just In Time) is a forum handle
-
07-05-2015, 09:34 PM #3
- Join Date
- Mar 2015
- Location
- CA
- Posts
- 693
- Blog Entries
- 1
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
Found more damage today when I was lubing my slide seals.
Upper corners of each slide outside frame have screws that poke through and cause slight tears as seen here.
Also noticed damage to seals on top of each slide, caused by protruding screw heads.
Put a dollop of sealant on each screw to see if that will help, hoping the sealant will dry before we leave tomorrow
John, Susan & Luke
2015 Reflection 303 RLS #867
Bakersfield, CA
-
07-06-2015, 09:31 AM #4
- Join Date
- Mar 2014
- Location
- Virginia Beach, VA
- Posts
- 251
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
07-09-2015, 11:21 PM #5
- Join Date
- Mar 2015
- Location
- CA
- Posts
- 693
- Blog Entries
- 1
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
Yes. I sent Jerry an email yesterday, he rogered up and will be sending me the strips.
We couldn't be happier with GD service, haven't called/emailed that many times, but they've got right on it every time.John, Susan & Luke
2015 Reflection 303 RLS #867
Bakersfield, CA
-
07-10-2015, 08:45 AM #6
- Join Date
- Nov 2013
- Location
- Gore Bay, Ontario
- Posts
- 2,171
- Blog Entries
- 6
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Did they provide some info in regards to the installation of the new slide seals? It's a swipe on top that should flip over against the slide floor when extending/retracting. It looks like the original was installed too high and the swipe damaged when extending/retracting the slide.
DaveDave and Monica - Gore Bay, Ontario
Vitus the Hungarian Vizsla
2014 Reflection 337 RLS #129
2008 F250 V10 CC Lariat RWD
-
07-13-2015, 11:27 PM #7
- Join Date
- Mar 2015
- Location
- CA
- Posts
- 693
- Blog Entries
- 1
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
No info yet.
John, Susan & Luke
2015 Reflection 303 RLS #867
Bakersfield, CA
Similar Threads
-
Rubber Slide Seals
By Paul & Deb in forum General DiscussionReplies: 37Last Post: 10-24-2021, 03:24 PM -
337RLS Slide Seals ... Normal?
By gr8daggett in forum ExteriorReplies: 5Last Post: 11-21-2020, 07:35 AM -
Slides and slide seals...spring maintenance in general
By Captain Skippy in forum General DiscussionReplies: 12Last Post: 05-01-2017, 07:12 PM -
Cleaning the rubber seals on Your slide outs
By 82alaska in forum General DiscussionReplies: 2Last Post: 07-03-2016, 11:08 PM -
Slide out seals, how often do you need to clean and lubricate them?
By The_Mit_375RE in forum General DiscussionReplies: 0Last Post: 04-18-2016, 08:50 AM
Slide actuator failure on 2021...
Today, 02:45 PM in General Discussion