User Tag List
Thanks: 0
Likes: 0
Results 11 to 20 of 29
Thread: Onan Cummins Generator Install
-
07-14-2016, 11:19 PM #11
- Join Date
- Dec 2014
- Location
- Carlsbad, CA
- Posts
- 2,959
- Mentioned
- 10 Post(s)
- Tagged
- 3 Thread(s)
Mine doesn't even touch the floor, it takes none of the weight of the generator. The generator frame is bolted to the trailer frame going side to side between the main frame. I might have a picture somewhere or I could take one if needed. I do have a couple square holes in the floor. One was necessary for the exhaust pipe to exit.
One thing I learned was to cover any openings in the floor with a wire mesh or rodents can get in and make a nest inside your generator. Ask me how I know!Paul "Poppy" and Deb Cervone
2022 Imagine XLS 22MLE
2021 Imagine XLS 17MKE - SOLD ; 2015 Grand Design Reflection 337RLS - SOLD
2016 GMC Denali 3500HD SRW Duramax/Allison CC 4x4; Tire Minder TPMS
-
07-15-2016, 06:46 AM #12
- Join Date
- Apr 2015
- Location
- Roundup, MT
- Posts
- 302
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I'm not sure how the Solitude frame is structured, but in my Momentum the gen sits on that thin floor getting a little support from the shield around it. When I did my solar installation I noticed that the floor sagged a little in the middle and I didn't think it would support 400lbs of batteries. We added a 2in square, .25in walled beam across the frame about a foot back (to allow access to the generator oil filter etc.) and some heavy aluminum angle bar to support the front. Now, nothing sags and nothing is going to fall out while travelling. All that stuff adds to the pin weight, so you have to make sure your truck can handle it.
Keith Regli
2016 Momentum 388m
2015 Silverado 3500HD DRW
[SIGPIC][/SIGPIC]
-
07-15-2016, 08:45 AM #13
- Join Date
- Jan 2016
- Location
- Minneapolis
- Posts
- 87
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
My Momentum also has no support for the Generator besides the thin floor, but it is supporting it just fine. On my thin floor there were 2 section to cut out for cooling. Once the generator was bolted in; it stiffened the whole floor.
-
07-15-2016, 08:53 AM #14
-
07-15-2016, 03:22 PM #15
- Join Date
- Dec 2014
- Location
- Carlsbad, CA
- Posts
- 2,959
- Mentioned
- 10 Post(s)
- Tagged
- 3 Thread(s)
Paul "Poppy" and Deb Cervone
2022 Imagine XLS 22MLE
2021 Imagine XLS 17MKE - SOLD ; 2015 Grand Design Reflection 337RLS - SOLD
2016 GMC Denali 3500HD SRW Duramax/Allison CC 4x4; Tire Minder TPMS
-
07-18-2016, 07:43 AM #16
- Join Date
- Apr 2015
- Location
- arkansas
- Posts
- 46
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
what is the material you used for the sound proofing of the generator compartment? and where may it be purchased?
Carl and Diane - Arkansas
2017 Grand Design Solitude 369RL
2020 CHEVY 2500 HIGH COUNTRY DURAMAX
Companion 5th wheel
-
07-18-2016, 08:43 AM #17
- Join Date
- Dec 2014
- Location
- Carlsbad, CA
- Posts
- 2,959
- Mentioned
- 10 Post(s)
- Tagged
- 3 Thread(s)
Paul "Poppy" and Deb Cervone
2022 Imagine XLS 22MLE
2021 Imagine XLS 17MKE - SOLD ; 2015 Grand Design Reflection 337RLS - SOLD
2016 GMC Denali 3500HD SRW Duramax/Allison CC 4x4; Tire Minder TPMS
-
07-18-2016, 11:14 AM #18
- Join Date
- Apr 2015
- Location
- arkansas
- Posts
- 46
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks I will check this out.
Sent from my iPad using TapatalkCarl and Diane - Arkansas
2017 Grand Design Solitude 369RL
2020 CHEVY 2500 HIGH COUNTRY DURAMAX
Companion 5th wheel
-
07-18-2016, 12:48 PM #19
- Join Date
- Jan 2016
- Location
- Minneapolis
- Posts
- 87
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
I ordered mine from http://wricointernational.com/
-
07-19-2016, 09:48 AM #20
- Join Date
- Feb 2016
- Location
- Tulsa, OK
- Posts
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Update.
I ordered mine directly through Cummins, got a 6500LP for $4,800. Way better than anything I found online.
I finally got it installed with the help of my Father-In-Law. Sure was nice when we had a derecho come through and were without power for a few days.
We ended up setting it on a cooler in front of the compartment, then using a piece of 1" plywood as a ramp to get it up and over the lip into the compartment. After that it was fairly easy hooking up the LP line and the electrical. Found out that one of my batteries isn't charging as it wouldn't crank the generator. Need to look further into that. FYI, if you're doing it yourself you'll need the exhaust kit that is purchased separately. Is it just me or does it take everyone else 2-3 trips to the store to finish a project.
Similar Threads
-
Cummins Onan Generator Installation
By Gary & Margo 2017 in forum Solar Systems and GeneratorsReplies: 34Last Post: 12-07-2023, 07:28 AM -
Onan 5500 gas generator with pusher pump, marine water separator 10 micron filter.
By scott42blue in forum Mods and DIYReplies: 9Last Post: 08-29-2022, 11:29 AM -
Fuel Treatment - Onan Generator
By VentureRider in forum General DiscussionReplies: 17Last Post: 04-17-2017, 11:36 PM -
Cummins ONON Generator LCD question
By JohnTassi in forum General DiscussionReplies: 3Last Post: 05-01-2016, 10:43 AM -
Pros/cons to NOT including Onan generator in your Momentum
By pg_rider in forum General DiscussionReplies: 22Last Post: 04-16-2015, 08:30 PM
Hello from Idaho
Today, 05:36 PM in Welcome Mat | New Member Introductions