User Tag List
Results 1 to 7 of 7
-
07-08-2016, 03:02 PM #1
- Join Date
- Feb 2015
- Posts
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Kitchen & Bedroom Slide Adjustment
I have 2016 Reflection 313 RLTS, the kitchen and bedroom slides are out of adjustment on the bottom they flush up pretty well on top but are about 1.5 to 3" out on bottom, not really against seal on bottom. Anyone have suggestions for dealing with this problem. They are SCHWINTEK IN-WALL SLIDEOUT SYSTEM, and there is supposed to be a control box that I need to locate, any help with either of these would be appreciated.
-
07-08-2016, 03:52 PM #2
- Join Date
- May 2016
- Location
- Vancouver, BC
- Posts
- 17
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I Have the same trailer, I found what I thought was the control box, in the pass thru storage compartment beside the utility panel. on the left side. On the roof of compartment.
-
07-08-2016, 04:48 PM #3
- Join Date
- Nov 2013
- Location
- Gore Bay, Ontario
- Posts
- 2,171
- Blog Entries
- 6
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Dave and Monica - Gore Bay, Ontario
Vitus the Hungarian Vizsla
2014 Reflection 337 RLS #129
2008 F250 V10 CC Lariat RWD
-
07-08-2016, 04:48 PM #4
- Join Date
- Aug 2015
- Location
- Iowa
- Posts
- 17
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
The control box does nothing for the top to bottom adjustment, it only keeps the slide motors synced front to back. There is a motor at the top (one at the front and one at the rear of the slide) with a shaft connected to gears that drive the top and bottom of the slides. My 313 has the same large gap at the bottom and small gap at the top and is at the dealer right now because of binding in my kitchen slide. I'm not sure how to adjust top to bottom but it does not appear to be easy.
-
07-12-2016, 11:22 AM #5
- Join Date
- Feb 2016
- Posts
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have a 385 Solitude and both large slides always seemed like they where in a bind. Bottom starts out first then the top lean out pretty extreme on the top and the bottom
then pushes out. Easter weekend we went out and I went to open my slide and my table side, it moved about 3 inches and stopped. Went and looked and the bracket had broken completely off. I have a service contract which was a waste off money because they don't work on the weekends when most people are camping. I went to Home Depot and bought a welder, grinder and all that it took to fix it and $ 800.00 later I'm good to go. I adjusted both slides when I fixed it and they operate smoothly now but they still lean out a lot at the top. I don't think they have anything controlling the top.
-
07-12-2016, 01:15 PM #6
- Join Date
- Nov 2013
- Location
- Gore Bay, Ontario
- Posts
- 2,171
- Blog Entries
- 6
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Those slide rooms are just like a big, open end box lying on it's side. The drive mechanism is only on the bottom so it's the first to move and last to stop when extending or retracting.
DaveDave and Monica - Gore Bay, Ontario
Vitus the Hungarian Vizsla
2014 Reflection 337 RLS #129
2008 F250 V10 CC Lariat RWD
-
06-01-2021, 10:45 AM #7
- Join Date
- May 2020
- Posts
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Similar Threads
-
Brake Adjustment Q, torque wrench & basement key
By ctangolf in forum General Tech TopicsReplies: 7Last Post: 02-13-2015, 09:01 AM -
Does this slide need adjustment?
By 2hams in forum ExteriorReplies: 9Last Post: 07-14-2014, 06:51 AM -
Does this slide need adjustment?
By 2hams in forum ExteriorReplies: 6Last Post: 07-12-2014, 09:09 AM
TCL TV turns on by itself after...
Today, 08:03 PM in Electronics