Black tank emptying and slide sticking.

TwilightTime

Member
Joined
Jul 26, 2021
Messages
18
I have a 2020 2500RL Imagine and the slide is out of sync. I have tried re-syncing/timing, back and forth 8 or so inches in and out both in and extended. This does not seem to solve anything. The bath room side still has to catch up about 3 inches after the theater seat side completes upon retract. Now, sometimes the bathroom side stops after after starting to retract after about 5 inches in, to get it going again I extend all the way then try again. Is there another reset? Thoughts?

With the black tank, when you attach the input water to flush the black tank from the side plug, does it just fill or does it spray as if to "clean the walls of the tank?

On another note, I noticed the black tank not completely emptying. Granted I was not on completely level ground so I am assuming this might have been the cause. Anyone know if the tank has a low center point drain or if its flat and needs a truly level surface when draining?

Many thanks for any help.
 
No problem, just was curious if you were going by the gauges, as they are notoriously inaccurate. The tank exits should be the low point of the tank.
It would depend on how unlevel you were.

Is the slide a Schwintek?

Most of the black tank rinse are a spray.
 
No problem, just was curious if you were going by the gauges, as they are notoriously inaccurate. The tank exits should be the low point of the tank.
It would depend on how unlevel you were.

Is the slide a Schwintek?

Most of the black tank rinse are a spray.

#1 Thats what I thought but imagine my surprise when my tank ran clear as I flushed it, yet when I looked down in to confirm there was still waste. That was a real head scratcher. I hope it was just un level enough to cause this because I would have absolutely no other explanation.

#2 Yes a Schwintek

#3 If it is a spray that makes it even more head scratching given the spray would likely hit most of the tank clearing the un level side still holding waste.
 
Are you leaving the valve closed on the black tank until you drain it? How out of level were you?

Are both of the slides Schwintek?
 
Imo the rinser is worthless when leaving the valve open


2021 Imagine 2400 BH
2018 GMC Sierra 4x4 crew
 
Imo the rinser is worthless when leaving the valve open


2021 Imagine 2400 BH
2018 GMC Sierra 4x4 crew

I agree, I close the black tank valve and fill it up about a quarter with the rinse-out connection, then I dump the tank. I repeat this procedure until the tank runs clear.
 
Are you leaving the valve closed on the black tank until you drain it? How out of level were you?

Are both of the slides Schwintek?

#1 As I flushed with fresh water, the black tank knife valve was open as I watched it run clear. When "empty" it was not completely empty upon inspection looking down in.

How level was I? It appeared "slightly" out may 3-4 degrees or so. But certainly if there were a center low point drain, the amount of level I was out should not seem to be an issue. I hope I'm wrong.
I should find a level dump before I get to crazy.

I have 1 slide out. I assume both side of the slide are the same. Sorry for any confusion.
 
In other words you really need to fill it to get a good flush?

I close the valve and measure 25-30 gallons then dump
I sometimes repeat this 3 times
Even on the third one there will still be TP flowing out


2021 Imagine 2400 BH
2018 GMC Sierra 4x4 crew
 
#1 As I flushed with fresh water, the black tank knife valve was open as I watched it run clear. When "empty" it was not completely empty upon inspection looking down in.

How level was I? It appeared "slightly" out may 3-4 degrees or so. But certainly if there were a center low point drain, the amount of level I was out should not seem to be an issue. I hope I'm wrong.
I should find a level dump before I get to crazy.

I have 1 slide out. I assume both side of the slide are the same. Sorry for any confusion.

I suppose the only way to ask is to be bold - do you use lots of water when flushing? Is it possible that, when "looking down" there you're seeing the dreaded dried poop pyramid?
 
I suppose the only way to ask is to be bold - do you use lots of water when flushing? Is it possible that, when "looking down" there you're seeing the dreaded dried poop pyramid?

Yeah, I wondered that, which was why I asked if the OP was keeping the valve closed, and therefore water in the tank, and only opening the valve when it's
time to dump the black tank.
 
In other words you really need to fill it to get a good flush?

Yes,
Water is your friend on a black tank flush. I connect the flush, run for a few minutes, then open the valve. Let it empty, then close the valve and fill about 1/2 way and then dump again. repeat until I am running clear. YMMV

What has not been mentioned is black tank treatment. We use the geo method and it has worked well for us.
 
Before I knew you could buy one I made my own toilet wand. I have a clear elbow for the outlet and I get a lot more "stuff" out using the wand even after using the on-board flush. I can actually get the sensor to read "Empty" using the wand.
 
I put a bag of ice in mine occasionally between campsites. This helps break up anything stuck to the bottom of the tank. I also let my tank fill at least half way and then top it off with water to get some good head pressure. So far, so good.
 
I had a problem with one of my slides as well. One side would come in all the way and not the other. I had checked the floor and walls where the slide would come in and there was nothing that appeared to be blocking it. After multiple attempts at resetting the slide, I finally decided to open the slide out halfway. I then checked under the bed/head board, and there it was. My long lost mini alarm clock. Problem solved. Hope you find the cause of your issue.
 
Several things we have found that help with the black tank.
1-Use plenty of water, if you have it with each flush
2-Add water, if you have it, at the end of your trip before you head to the dump station. This will allow the water to slosh around in the tank on the way to the dump station. This sloshing around helps to break things up and loosen them from the walls of the tank.
3-Use the tank sprayer to fill more water at the dump station with the valve closed. Again as has been mentions creating a bit of head to help things flow out.
4-Don't always dump at the nearest dump station in the campground. Let that extra water you added slosh around while on the road to your next campground. I wouldn't do this if you will be boondocking.
5-Our city has a free dump station so we can dump at the campground the majority of the stuff, add sloshing water for the trip home and then dump the cleaning stuff at the city station. With a clear elbow you will be able to see the difference.
 
I have a 2020 2500RL and I have noticed that I need to be pretty level or even leaning a bit towards the driver side to get the tanks to flush well. I always dump then close the valve; flush for 3-4 minutes (filling the thank); dump again and repeat until it runs clear.
 
I think I have the same problem with my black tank on my 21BHE. After draining, as in nothing else coming out of the drain hose, I can look down my toilet and still have about 1/2" (measured with a stick) of fluid in the bottom of the tank. My local service department says that is normal, but I'm skeptical. Reached out to GD about it, but they have not responded.
 

New posts

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top Bottom