Blasphemy!! Riverstone 5th Wheel vs Solitude

Any update on the new rig?
Things are going well so far. A few annoying albeit minor issues. We took our first drive - a total trial by fire going from Atlantic City NJ to upstate NY - taking the i95 corridor was the craziest drive we've ever tried! I never felt unsafe, it’s just on/off/on the highways, running down state routes just outside of NYC - it was stressful. But the Riverstone drives beautifully. The Hensley air ride hitch really smooths things out, and, with the triple axles, the rig is very well balanced and doesn’t put a whole lot more weight in the TV than the Solitude did. I need to find a CAT scale one of these days to validate all the weights.

Otherwise it’s a great rig and the dealer was great - White Horse in NJ. They’re independent so not all the corporate BS you get at places like Camper World.

My only real complaint so far is they are putting brand new AC/Heatpump units in the ’26 models, one I had never heard of before: Gree. There seem to be some hiccups with those units:
1 - When the ACs are on full time (ie the fans on and not on Auto), we’re getting some outside air intrusion. Sitting in soggy NJ last week and letting the ACs run all night, we were 80% humidity in the rig in the AM - totally unacceptable.
2 - The sensors for each of the HVAC units are apparently in the return ducts, which is about the stupidest engineering decision I’ve heard of. On a hot day, when only 1 is running, cold air is feeding back through the loop some, which gives false (too cold) readings on the 2 & 3 unit that are not running. This leaves one unit running and struggling and the other 2 not running. The solution to this from Riverstone was to keep the AC fans running - hence how we discovered problem #1.

I have the Service Manager from White Horse following up with Riverstone to see if there is some mitigation I can do - seal better around the units maybe for the air intrusion, and can they retrofit some of the older style wall sensors they used to use on previous years. My supposition is they might have switched out the ACs without updating the holes for them in the roof, and they don’t seal in as good as the previous Dometic units did. I can manage all this by keeping a close eye on the temp during the day - need to leave the ACs on Auto, and then kick the fans on for a few minutes here and there to equalize the temps. Annoying but at least we weren’t soaking wet last night for the first time. I do have a small dehumidifier arriving today, so that’ll help. But these 2 issues together tell me they didn’t to enough testing into these new Gree units - which otherwise are quiet and seem to work well, when they do kick on.

Otherwise, things are good. The Furrion Vision + system with 4 cameras makes driving this beast much more comfortable. I didn’t use a back camera on the Solitude, so the blind spot monitoring is nice. The side view cameras are overkill on the road, but great for spotting down the blind side when backing/turning.

The Riverstones also come with the new Lippert Waste Master cam-locking hose system. That’s pretty cool and works well, but I didn’t know this going into the deal so I had bought $100 worth of new stinky slinky gear that’s worthless now - a y-connector and better connection lock elbow. There are no y-connectors for this, so I’m running the hose back & forth between tanks for now - not a big deal at all.

All in all, we’re very pleased with our decision and purchase.

BTW, on that note people like to look at the numbers:
Retail $215,000
Sale price: $154,000 +$1500 for the ecopro seal inside & out, +$2500 for extended warranty (wasn’t going to do the warranty but they gave it to us for dealer pricing and that amount seems reasonable for a fulltime rig).

Considering all you get with a Riverstone (body paint, dual pane windows, disk breaks, camera system & TPMS installed, and the washer & dryer) they are worth a look if you’re looking at the large Solitudes. Once you add up all the extras it’ll cost you to match the standard equipment, the price is better IMO. For Solitudes now, the body paint alone is $18k, for example.
 
Update on 3 months full time in the Riverstone. We’ve managed to not murder each other or any of the animals, so, all in all, that’s a success! The rig is super comfortable for full timing, really no complaints other than the standard new rig a bit of trim loose here and there, and the aforementioned HVAC issue (have that corrected now after some work with Riverstone and Gree. Short story is I had Gree send me 25ft sensor cables and ran the sensors through the air return and into the cabin. It’s not the cleanest look in the world, with a small black wire coming out and secured to the wall or ceiling, but everything works properly now. Main issue is putting the sensors up in the air return, above the ceiling. Very dumb placement and I still have no idea how it made it through QA and into production. Previous years they ran the wires through the walls and into a little wall-mounted cover. Hopefully they return to that model).
Otherwise one break line recall but no other issues.
Our main problem has been with the lack of good full time options in the Charlotte area. We’ve settled into a county park, that has awesome sites, several miles of walking trails, and a very reasonable rate. However, they discourage full timing, so we have to move sites every 2 weeks.

We’ve logged about 5000 miles, going from NJ > Lake George NY > Niagara Falls > Columbus Ohio > Charlotte, NC > Johnson City TN > Charlotte > Roanoke, VA > back to Charlotte, and then off to Florida for a month later next week.

I continue to be impressed with how smoothly and easily the rig tows - triple axle with disk brakes makes for excellent balance and phenomenal stopping power vs our Solitude 310. Part of that smoothness is the Hensley Trailer-saver hitch, which I highly recommend for big rigs. it’s the only hitch with fully integrated airbags and shocks.

The 44dbl model has given us everything we need. The office is awesome for me to have during the day. However, that’s a lot of living space that doesn’t get used much back here. The extra bathroom is great. If we could do it all over again, in a perfect world I think we’d go with the new 43bfc model that’s just coming out now. Better use of space for us and still has a half bath. But those are very, very minor quibbles. Even with all this space lost in the office, the bedroom, bath, and living/kitchen areas are all well-appointed and just enough for us. Even with 3 (small) dogs and a cat, we don’t feel crowded or packed in. The 8.5ft ceilings really help with that.

Having all 3 HVAC units as heatpumps has been great during the cold fall evenings. We’ve only had to run the furnace a couple of times so far, and that works great also. Between the electric fireplace and the heat pumps, we’re good to go down to about 40 degrees (standard heat pump range).

I’m interested to see what/if Grand Design does with their triple-axle prototype, as seen on the Youtue channel Less Junk, More Journey. They were the couple that tested out what is the new bunkroom/office space rig. That was the Solitude we were going to buy until we looked at the Riverstones.

All in all, we’re very pleased and the worries about a Forest River product have not been an issue. The rig is, overall, build like the proverbial brick sh*% house. Very, very sturdy. Oh, I also love the one-piece fiberglass roof. Huge upgrade from the TPO most trailers utilize.

The one thing that feels extraneous and we don’t really need it is the single drawer dishwasher. If you have kids or 2 couples in this rig, it would be awesome. For the two of us, we’ve only used it a few times and I’d rather have that kitchen cabinet back for storage.

If anyone has any questions about making the switch, hit me up any time!

-Colin
 
Oh, I’ve also been impressed with the tankless hot water heater. I was worried that would burn through propane, but it’s very efficient. These latest generation ones even have a winter setting, where it’ll cycle hot water through the system periodically, to avoid the freezing people would encounter on the 1st gen units. I just topped off the propane last week - this rig has 2x 40lbs tanks. One was 1/4 full, the other half, so call that a little over 40lbs of gas in 2.5 months. I’ll see how the winter months go with propane usage, but Charlotte area isn’t that bad other than a few cold snaps in the winter. We’ll be able to get by on the heat pumps most of the time.
 
Glad to hear all the news Colin. Sounds like you two are enjoying the nomad life. Hope one day we can meet up with you both in the wild. Til then, safe travels.
Pete
 
JMO397...really nice update. Thanks for following up! Being a RAM dually owner, I'm curious how the truck is treating you. Any complaints or issues?
 
Valve body goes out in the transmission. Easy to look up. 400,000 recall on the 2020 to 2022 Duramax
I just returned from a 2 week trip at Bryce/Zion national parks. My Silverado and Momentum, including the much maligned fridge were both flawless.​
 
Congrats! Beautiful dually too!

Join the HDRams forum to keep an eye on issues and how to fix. Just don’t take any action until you’ve done some serious reading as just like any forum there’s a lot of noise. You’ll get to know who the good guys are pretty quickly and trust their advice.

Here are some items recommend after learning from my 2020 3500:

Install a CTS3 Edge in the cab (get the CTS Ram pillar mount for a clean install). This lets you monitor important items like:

Regen Status (on or off, so your EVIC screen can display tire pressure instead of regen)
Regen % (true status, not the dash dumb meter)
Time since last regen (if less than 1440 minutes, you know it’s doing active regens)
VGT (turbo) position (so you know if actuator is sticking)
DEF concentration% (so you know when you get bad DEF)
EGT sensors (so you know if exhaust is hot enough for passive regen)
Batt voltage (so you know when they are about to go bad after 5 years or so)
Etc

I’ve attached a picture of mine. Would never run a diesel emissions truck without it now.

As you can see in my pic before my time since last regen is only 545 minutes (instead of around 1440 minutes, it’s never exact). Rams have an automatic 24 hr regen cycle, if you have not actively regen’d due to soot loading, it will force a regen after after 24 hours of drive time. Really confuses people at first. They think something is wrong with the truck.

That number in the top left is from the ECU showing time since last regen, so if well under 1440 minutes (24 hrs) you know something is wrong and your truck is running active regens for some reason (driving habits, soot loading, wrong air filter, crappy fuel, etc etc etc). If it hovers around 1440 (like I said it’s never perfect), you’re in great shape. That means the truck has not required an active regents and is only running the 24 hr timed regens.

Note: Some of the guys on the HD ram forum ignore this number as they say it’s wildly inaccurate. I found it completely the opposite, especially since I monitor it every single day. Yes, it’s not an exact 24 hours but if it’s anything below 1000 you know somethings causing active regeneration cycles and you should keep an eye on things. If it’s well over 1200 or 1300 minutes you’re probably doing timed 24hr cycles and everything‘s good.

With the CTS3 you can also tell if you have a timed regeneration cycle coming up. The DPF soot loading percentage PID tells you the actual loading of the filter. The DPF gauge on the EVIC is a fake number that’s based upon what the ECU wants to do, so if you see the dash EVIC showing the soot level rising yet the CTS3 shows it much lower and not rising, you know the ECU is about to command a 24hr timed region cycle, not due to soot loading. It’s a small thing, but it’s nice to know for peace of mind.

Notice I mentioned the air filter, we have all determined through years of testing on the forum that these trucks are disgustingly sensitive to the air filter. Do not buy anything aftermarket unless it’s made by Cummins fleetguard which technically is not aftermarket. Stick to the OEM filter and make sure you get the exact part number that is required for your year of truck. There are different parts. When they put the 2022 part number filter in my 2020 truck it was disastrous, regening like crazy, simply installing the proper filter incredibly sold 99% of my issues.

Don’t deviate or you will regret it…. Well, your DPF filter will and since they’re non-serviceable on pick up trucks, you don’t want that headache. Anything in the air intake tract can cause the region status to go a little crazy, loose band clamps to the turbo, flashing on the plastic housings, etc. Just keep a good eye on that and keep it in good shape. Replace that filter more often and give it a good cleaning more often. Your truck will thank you.

Same thing goes for the DEF fluid. Never let it go too far below 50%. That’s the exact spot (or just below it) where you can put in a full jug without it overflowing. Things start to happen when you have low DEF on all trucks. The fluid you buy is totally up to yourself, but while it’s under warranty, I exclusively used the dealership stuff. It wasn’t much more than all the offbrand, but I had receipts to prove that I use the correct stuff if we ever had a DEF warranty issue. Now that I can measure the concentration using the CTS 3 edge (33% is the sweet spot) I feel a little more comfortable going off brand once the warranty is done.

Download a program for your phone like Road Trip, log all your fuel fill-ups and service items. These trucks require a fair bit of maintenance and won’t give you much trouble as long as you follow them. Most of the service on this truck is very easy to do. None of it is hard. I do it right in the driveway or at campsites without issue.

Using Road Trip add in the proper service intervals from your owners manual for the following:

-Fuel Filters
-Air Filter (hugely critical item on this truck, replace often, especially when regens start happening for no reason)
-Oil Change (very important here due to possible fuel contamination, she’s a dirty girl)
-Tire Rotation
-Brake Pad/caliper Lubrication (amazing how simply putting the Smurf poop on the callipers and pads makes such a difference in the smooth operation)
-Cabin air filter (not a critical item, but good to know when it needs to be replaced)
-Asin Transmission Fluid change (very easy to do, and very critical for that tranny. Make sure you buy the exact correct fluid. It’s very specific).
-Asin transmission filter change (again, very easy to do and critical)
-CCV filter change (do not miss this change interval, it’s not something you want to experience)
-Transfer case fluid change
-Differential case fluid change (you take off the entire cover, the gasket is reusable, very easy to do as well. Use the Amsoil bagged fluid for easy service)
-Add a service reminder for end of engine warranty, which is great to track as well.

Also, keep track of your DEF fill ups. Etc, basically all service and expense items. It’s great to keep track of this info, but it also updates the mileage tracking which let you know when the service items are due.

If you keep track your fuel fill-ups Road trip will automatically keep track of your service mileage as well which let you know when things are due.

It is also a godsend when you start having weird issues you can look back in your logs and see what you’ve done differently such as switching to a different gas brand or using different DEF fluid, etc.

—-

Fuel additives is another one of those black arts that everyone has a personal favorite. Use whatever you prefer but the current trend on the forum seems to be using Archoil 6400 on the schedule interval, to help clean out the fuel system and filter and then either our Archoil 6500 every full-up or EDT or whatever you prefer.

The consensus seems to be the archoil 6400 treatment on the recommended interval, seems to help these trucks with rengen. But in speaking with service and parts counter guys, it’s the air intake and air filter that seems to make the most difference. Considering how expensive these trucks are and how much it sucks to have a derated truck while towing due to some stupid sensor, I just do both.

—-

You will love the air suspension as I’m sure you’ve already experienced never have to do anything with it. It just takes care of itself.

You may have already found out that the lower ride height button, which basically puts the overload springs in contact with the main leaf pack only works if you have enough payload in the bed otherwise it will abort. It’s a great trick. If you’re finding the ride a little bouncy it’s because the leaf pack may not be in constant contact with the overload springs though your trailer might be heavy enough to do this. Just look underneath when everything’s hooked up and see if all the leaves are in contact if not, just use the alternate ride height button and it will drop the suspension about 1 inch to put all the leaves in contact.

—-

The bane of this truck is the emissions, the DPF filter and regen. If you keep up on the maintenance, you’ll probably be fine with only the odd time where it wants you to really give it a good heavy regen you keep up on the maintenance, you’ll probably be fine with only the odd time where it wants you to really give it a good heavy regen but if you miss some of the items or let the air filter, get too dirty, you’ll be having an active regen every tank fill up.

If you ever see the message on the EVIC (Center dash) that says “exhaust system regeneration in process continue driving”, that means it has not been able to fully clear the DPF filter through normal regeneration cycles. It’s a dead serious message, if you’re not towing, go for a drive on some nice long roads and Lock the truck into Second or third gear. You can use the buttons on the wheel for this. Keeping it in second or third will cause the engine to work harder. Keep it around 2000 RPM or so this will help with the regeneration cycle and keep the heat into the exhaust. Then just keep driving until the regeneration cycle is done, if you have the CTS 3, you can monitor this accurately and also know if you’re getting the temperatures above 500 C/ 930 F, this truck regenerates well when it’s above those temperatures.

I just ran into one of these the other day because we’ve been taking the truck on short drives too much and not enough along Highway drives to let the passive regen do its job. I hit the back roads locked her in second gear and revved the crap out of it, and it got nice and hot and clean the filter completely out, I haven’t seen it start up at below 10% soot level in years.

—-

Until you use a bypass cable and ODB software to change the tire pressure monitoring keep the tire pressure monitor on your dash at all times when towing. You’ll have to check for your year of truck but for some dumb reason on the 3500s the tire pressure system is a monitor and not a warning system. It won’t alert you if your tire starts losing pressure thankfully you can use programming software to turn on the warning feature like the 2500’s have.

—-

Grab one of the cheap oil filter screw and plugs with the handle, it allows you to unscrew the oil filter and let it gently rest in the suspension and then you screw in the plug and you can pull the filter out through the wheel well without spilling a drop.

When you change oil filters, make sure the gasket comes off the engine flange as it’s a blind spot and if some numpty over tightened the last filter, the gasket may stay stuck to the engine.

—-

Send your oil into one of the labs at whatever interval you’re comfortable with so you can keep track of the health of the engine and know if you’re getting fuel contamination or other odd items. Very handy for peace of mind.

—-

Grab four of the Powerbuilt Unijack Bottle Jacks (locking jack stand with built in jack), they make it very easy to jack up the entire truck for service work. You may find you have to grind down the width of the front ones to fit in the suspension hangers on the front axle like I did. But now doing tire rotations, or any other major service is an absolute breeze as I can lift the truck securely and have locking jackstands for safety. Being in the US, you can get these for damn cheap when they come on sale usually Summit Racing or Amazon has them for half the price or less than we have to pay up in Canada. To rotate the tires unfortunately, you basically have to have the whole truck up in the air but it also makes it easy to service the brakes and check on those etc. only headache is they take up a fair bit of space if you keep them with you on the road, but you can come up with methods to store them easily. They also work well for lifting up trailer axles so pull double duty.

—

I’ll have to go through my notes I’m sure I have a ton of other tips but this is getting long lol!

I absolutely adore this truck and love that you can fill the DEF from the side instead of under the hood like other trucks.


Cheer and enjoy!
 

Attachments

  • IMG_5757.jpeg
    IMG_5757.jpeg
    109.8 KB · Views: 174
Last edited:
The underhood def fill on the GMs went away in 2020.
GM had it under the hood to prevent accidental misfills as they knew there would be some confusion with the new system. It worked, as I never read a report of a misfill on a GM.

The other brands DID have misfills. This was a $ 10,000 mistake.
Now, with most everyone famalier with def, it was a good time to move it to an easier location
 
The underhood def fill on the GMs went away in 2020.
GM had it under the hood to prevent accidental misfills as they knew there would be some confusion with the new system. It worked, as I never read a report of a misfill on a GM.

The other brands DID have misfills. This was a $ 10,000 mistake.
Now, with most everyone famalier with def, it was a good time to move it to an easier location
Now there's a company answer if I've ever heard one :) We put the DEF fill in a terrible spot to protect you from yourself! Thanks big brother!

The GM fill was a joke. Under the hood/different location is one thing. On the opposite side of the fuel fill is another. Drag the hose across the open engine compartment and fender to the other side to the back corner. Afterthought engineering at its best. I guess jugs may be a bit easier if you want to lift 2 1/2 gallons chest high and over the fender but under the hood. Those are last resort for me anyway. The only time I've ever had DEF issues/errors was from the jugs.
 
We have a 2020 Ram 3500 with HO Cummins and it tows our GD 360RL just fine. We also have 8k axles and disc brakes.

PS Please stop spelling "breaks" for brakes. I see that more and more these days.
 
Congrats! Beautiful dually too!

Join the HDRams forum to keep an eye on issues and how to fix. Just don’t take any action until you’ve done some serious reading as just like any forum there’s a lot of noise. You’ll get to know who the good guys are pretty quickly and trust their advice.

Here are some items recommend after learning from my 2020 3500:

Install a CTS3 Edge in the cab (get the CTS Ram pillar mount for a clean install). This lets you monitor important items like:

Regen Status (on or off, so your EVIC screen can display tire pressure instead of regen)
Regen % (true status, not the dash dumb meter)
Time since last regen (if less than 1440 minutes, you know it’s doing active regens)
VGT (turbo) position (so you know if actuator is sticking)
DEF concentration% (so you know when you get bad DEF)
EGT sensors (so you know if exhaust is hot enough for passive regen)
Batt voltage (so you know when they are about to go bad after 5 years or so)
Etc

I’ve attached a picture of mine. Would never run a diesel emissions truck without it now.

As you can see in my pic before my time since last regen is only 545 minutes (instead of around 1440 minutes, it’s never exact). Rams have an automatic 24 hr regen cycle, if you have not actively regen’d due to soot loading, it will force a regen after after 24 hours of drive time. Really confuses people at first. They think something is wrong with the truck.

That number in the top left is from the ECU showing time since last regen, so if well under 1440 minutes (24 hrs) you know something is wrong and your truck is running active regens for some reason (driving habits, soot loading, wrong air filter, crappy fuel, etc etc etc). If it hovers around 1440 (like I said it’s never perfect), you’re in great shape. That means the truck has not required an active regents and is only running the 24 hr timed regens.

Note: Some of the guys on the HD ram forum ignore this number as they say it’s wildly inaccurate. I found it completely the opposite, especially since I monitor it every single day. Yes, it’s not an exact 24 hours but if it’s anything below 1000 you know somethings causing active regeneration cycles and you should keep an eye on things. If it’s well over 1200 or 1300 minutes you’re probably doing timed 24hr cycles and everything‘s good.

With the CTS3 you can also tell if you have a timed regeneration cycle coming up. The DPF soot loading percentage PID tells you the actual loading of the filter. The DPF gauge on the EVIC is a fake number that’s based upon what the ECU wants to do, so if you see the dash EVIC showing the soot level rising yet the CTS3 shows it much lower and not rising, you know the ECU is about to command a 24hr timed region cycle, not due to soot loading. It’s a small thing, but it’s nice to know for peace of mind.

Notice I mentioned the air filter, we have all determined through years of testing on the forum that these trucks are disgustingly sensitive to the air filter. Do not buy anything aftermarket unless it’s made by Cummins fleetguard which technically is not aftermarket. Stick to the OEM filter and make sure you get the exact part number that is required for your year of truck. There are different parts. When they put the 2022 part number filter in my 2020 truck it was disastrous, regening like crazy, simply installing the proper filter incredibly sold 99% of my issues.

Don’t deviate or you will regret it…. Well, your DPF filter will and since they’re non-serviceable on pick up trucks, you don’t want that headache. Anything in the air intake tract can cause the region status to go a little crazy, loose band clamps to the turbo, flashing on the plastic housings, etc. Just keep a good eye on that and keep it in good shape. Replace that filter more often and give it a good cleaning more often. Your truck will thank you.

Same thing goes for the DEF fluid. Never let it go too far below 50%. That’s the exact spot (or just below it) where you can put in a full jug without it overflowing. Things start to happen when you have low DEF on all trucks. The fluid you buy is totally up to yourself, but while it’s under warranty, I exclusively used the dealership stuff. It wasn’t much more than all the offbrand, but I had receipts to prove that I use the correct stuff if we ever had a DEF warranty issue. Now that I can measure the concentration using the CTS 3 edge (33% is the sweet spot) I feel a little more comfortable going off brand once the warranty is done.

Download a program for your phone like Road Trip, log all your fuel fill-ups and service items. These trucks require a fair bit of maintenance and won’t give you much trouble as long as you follow them. Most of the service on this truck is very easy to do. None of it is hard. I do it right in the driveway or at campsites without issue.

Using Road Trip add in the proper service intervals from your owners manual for the following:

-Fuel Filters
-Air Filter (hugely critical item on this truck, replace often, especially when regens start happening for no reason)
-Oil Change (very important here due to possible fuel contamination, she’s a dirty girl)
-Tire Rotation
-Brake Pad/caliper Lubrication (amazing how simply putting the Smurf poop on the callipers and pads makes such a difference in the smooth operation)
-Cabin air filter (not a critical item, but good to know when it needs to be replaced)
-Asin Transmission Fluid change (very easy to do, and very critical for that tranny. Make sure you buy the exact correct fluid. It’s very specific).
-Asin transmission filter change (again, very easy to do and critical)
-CCV filter change (do not miss this change interval, it’s not something you want to experience)
-Transfer case fluid change
-Differential case fluid change (you take off the entire cover, the gasket is reusable, very easy to do as well. Use the Amsoil bagged fluid for easy service)
-Add a service reminder for end of engine warranty, which is great to track as well.

Also, keep track of your DEF fill ups. Etc, basically all service and expense items. It’s great to keep track of this info, but it also updates the mileage tracking which let you know when the service items are due.

If you keep track your fuel fill-ups Road trip will automatically keep track of your service mileage as well which let you know when things are due.

It is also a godsend when you start having weird issues you can look back in your logs and see what you’ve done differently such as switching to a different gas brand or using different DEF fluid, etc.

—-

Fuel additives is another one of those black arts that everyone has a personal favorite. Use whatever you prefer but the current trend on the forum seems to be using Archoil 6400 on the schedule interval, to help clean out the fuel system and filter and then either our Archoil 6500 every full-up or EDT or whatever you prefer.

The consensus seems to be the archoil 6400 treatment on the recommended interval, seems to help these trucks with rengen. But in speaking with service and parts counter guys, it’s the air intake and air filter that seems to make the most difference. Considering how expensive these trucks are and how much it sucks to have a derated truck while towing due to some stupid sensor, I just do both.

—-

You will love the air suspension as I’m sure you’ve already experienced never have to do anything with it. It just takes care of itself.

You may have already found out that the lower ride height button, which basically puts the overload springs in contact with the main leaf pack only works if you have enough payload in the bed otherwise it will abort. It’s a great trick. If you’re finding the ride a little bouncy it’s because the leaf pack may not be in constant contact with the overload springs though your trailer might be heavy enough to do this. Just look underneath when everything’s hooked up and see if all the leaves are in contact if not, just use the alternate ride height button and it will drop the suspension about 1 inch to put all the leaves in contact.

—-

The bane of this truck is the emissions, the DPF filter and regen. If you keep up on the maintenance, you’ll probably be fine with only the odd time where it wants you to really give it a good heavy regen you keep up on the maintenance, you’ll probably be fine with only the odd time where it wants you to really give it a good heavy regen but if you miss some of the items or let the air filter, get too dirty, you’ll be having an active regen every tank fill up.

If you ever see the message on the EVIC (Center dash) that says “exhaust system regeneration in process continue driving”, that means it has not been able to fully clear the DPF filter through normal regeneration cycles. It’s a dead serious message, if you’re not towing, go for a drive on some nice long roads and Lock the truck into Second or third gear. You can use the buttons on the wheel for this. Keeping it in second or third will cause the engine to work harder. Keep it around 2000 RPM or so this will help with the regeneration cycle and keep the heat into the exhaust. Then just keep driving until the regeneration cycle is done, if you have the CTS 3, you can monitor this accurately and also know if you’re getting the temperatures above 500 C/ 930 F, this truck regenerates well when it’s above those temperatures.

I just ran into one of these the other day because we’ve been taking the truck on short drives too much and not enough along Highway drives to let the passive regen do its job. I hit the back roads locked her in second gear and revved the crap out of it, and it got nice and hot and clean the filter completely out, I haven’t seen it start up at below 10% soot level in years.

—-

Until you use a bypass cable and ODB software to change the tire pressure monitoring keep the tire pressure monitor on your dash at all times when towing. You’ll have to check for your year of truck but for some dumb reason on the 3500s the tire pressure system is a monitor and not a warning system. It won’t alert you if your tire starts losing pressure thankfully you can use programming software to turn on the warning feature like the 2500’s have.

—-

Grab one of the cheap oil filter screw and plugs with the handle, it allows you to unscrew the oil filter and let it gently rest in the suspension and then you screw in the plug and you can pull the filter out through the wheel well without spilling a drop.

When you change oil filters, make sure the gasket comes off the engine flange as it’s a blind spot and if some numpty over tightened the last filter, the gasket may stay stuck to the engine.

—-

Send your oil into one of the labs at whatever interval you’re comfortable with so you can keep track of the health of the engine and know if you’re getting fuel contamination or other odd items. Very handy for peace of mind.

—-

Grab four of the Powerbuilt Unijack Bottle Jacks (locking jack stand with built in jack), they make it very easy to jack up the entire truck for service work. You may find you have to grind down the width of the front ones to fit in the suspension hangers on the front axle like I did. But now doing tire rotations, or any other major service is an absolute breeze as I can lift the truck securely and have locking jackstands for safety. Being in the US, you can get these for damn cheap when they come on sale usually Summit Racing or Amazon has them for half the price or less than we have to pay up in Canada. To rotate the tires unfortunately, you basically have to have the whole truck up in the air but it also makes it easy to service the brakes and check on those etc. only headache is they take up a fair bit of space if you keep them with you on the road, but you can come up with methods to store them easily. They also work well for lifting up trailer axles so pull double duty.

—

I’ll have to go through my notes I’m sure I have a ton of other tips but this is getting long lol!

I absolutely adore this truck and love that you can fill the DEF from the side instead of under the hood like other trucks.


Cheer and enjoy!
Whoa! Lots of good information here. I'm kind of a techie so I enjoy all this stuff. That said, I'm on my second RAM Cummins and I've just done all my maintenance by the book with no issues or special monitors. I say this for the average guy looking for a new truck and might be interested in RAM. The RAM Cummins is really no different than the other offerings from Ford and GM. I totally agree that you gotta stay on top of things like regular oil changes, air and fuel filters (OEM only for me), fresh fuel from stations that have a good diesel turnover, and fresh DEF - but those are true with any of the big 3 diesel engines. Maintain your RAM as the manual recommends and it will treat you well.
 
Whoa! Lots of good information here. I'm kind of a techie so I enjoy all this stuff. That said, I'm on my second RAM Cummins and I've just done all my maintenance by the book with no issues or special monitors. I say this for the average guy looking for a new truck and might be interested in RAM. The RAM Cummins is really no different than the other offerings from Ford and GM. I totally agree that you gotta stay on top of things like regular oil changes, air and fuel filters (OEM only for me), fresh fuel from stations that have a good diesel turnover, and fresh DEF - but those are true with any of the big 3 diesel engines. Maintain your RAM as the manual recommends and it will treat you well.
Agree. I'm on my 3rd Ram. One was a 2500 Hemi so it doesn't count. LOL

I don't do anything other than reg maintenance. I don't tow real heavy but do tow 4000-5000 miles a year. The rest 2500-3000 is just daily driver errand running since I'm retired. I do get DPF auto regen messages a few times during the winter. When I do and if convenient I take it out to the freeway and run up and back about 15-20 miles and that usually clears it up. Going on 6 years with my 2019 3500 and it's still treating me well. I buy at brand name fuel stations but 99% of the time I just buy box DEF where it's convenient.
 

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top Bottom