missadventuring
Member
Hi all - hoping to tap the collective experience here before I commit to a repair path. Also hoping someone can help me nail down a spec I can't confirm on my own.
Rig: 2016 Grand Design Solitude 321X, stationary (no near-term travel), Morgan Hill/Gilroy/San Jose, CA area.
Awning: Carefree Travel'r, front door-side, fixed (non-adjustable) - no pitch-adjustment mechanism on the arm.
Not sure if mine is Flat Pitch or Steep Pitch. What I know:
- Door clearance (top of door to awning rail): 25"
- Haven't extended the awning to check the actual drop angle (see issue #1 below - trying to avoid operating it until the mount is assessed), but eyeballing the folded arm, it looks more like a flat-pitch profile to me than steep - not confident though.
- If it matters: Carefree's spec has Flat Pitch dropping ~12" when extended vs. Steep Pitch dropping ~36" - if anyone knows a way to tell the pitch type from the closed/folded arm without extending, that would solve this for me.
Two separate issues:
1. Front-end arm mount is separating from the sidewall. Arms and motor are fine - isolated to the wall attachment point. Haven't extended the awning since noticing this. Trying to determine: loose/failed mounting hardware (Carefree Quick Mount Bracket Kit territory) vs. wall substrate damage behind the mount. Anyone dealt with this exact failure on a Travel'r?
2. Fabric has significant tears on both ends and thinning all along the attachment edge - not just one localized tear. Saw a thread here about fabric rotting at the attachment seam possibly tied to storing it wet/mold - checking mine for similar staining.
What I've got so far:
- Rail/fabric width approx 162" (working out to ~14' nominal on Carefree's sizing)
- Carefree canopy-only fabric quote: ~$810 (fabric + shipping)
- Considering ShadePro sealed-edge fabric instead, based on a thread here where an owner preferred it over Carefree's sewn-edge fabric
- Planning a mobile tech visit to diagnose the mount and handle the fabric R&R together
One wrinkle if it comes to arm replacement: I understand Fixed Flat Pitch arms are now NLA/discontinued per Carefree's own parts list, while Steep Pitch arms are current stock. With 25" of door clearance, I could apparently go to Steep Pitch arms if needed (needs 15.5", Flat needs 7") - but would rather know what I actually have before assuming I need a workaround.
Questions for anyone who's been through this:
- Any way to tell Flat vs Steep pitch without extending the awning? (At this point do I care about further damage from extending the awning?)
- Front mount separation - hardware or substrate, in your experience?
- Anyone had a Travel'r mount issue covered under warranty or recall (found NHTSA 14E065000 / 14E078000 for Carefree Latitude brackets - unclear if related)?
- ShadePro vs. Carefree fabric experience on a Travel'r?
- Fair price range for a mobile tech to do combined mount diagnosis + fabric R&R at this size?
Appreciate any input - trying to make one good decision here rather than a string of small ones.
Rig: 2016 Grand Design Solitude 321X, stationary (no near-term travel), Morgan Hill/Gilroy/San Jose, CA area.
Awning: Carefree Travel'r, front door-side, fixed (non-adjustable) - no pitch-adjustment mechanism on the arm.
Not sure if mine is Flat Pitch or Steep Pitch. What I know:
- Door clearance (top of door to awning rail): 25"
- Haven't extended the awning to check the actual drop angle (see issue #1 below - trying to avoid operating it until the mount is assessed), but eyeballing the folded arm, it looks more like a flat-pitch profile to me than steep - not confident though.
- If it matters: Carefree's spec has Flat Pitch dropping ~12" when extended vs. Steep Pitch dropping ~36" - if anyone knows a way to tell the pitch type from the closed/folded arm without extending, that would solve this for me.
Two separate issues:
1. Front-end arm mount is separating from the sidewall. Arms and motor are fine - isolated to the wall attachment point. Haven't extended the awning since noticing this. Trying to determine: loose/failed mounting hardware (Carefree Quick Mount Bracket Kit territory) vs. wall substrate damage behind the mount. Anyone dealt with this exact failure on a Travel'r?
2. Fabric has significant tears on both ends and thinning all along the attachment edge - not just one localized tear. Saw a thread here about fabric rotting at the attachment seam possibly tied to storing it wet/mold - checking mine for similar staining.
What I've got so far:
- Rail/fabric width approx 162" (working out to ~14' nominal on Carefree's sizing)
- Carefree canopy-only fabric quote: ~$810 (fabric + shipping)
- Considering ShadePro sealed-edge fabric instead, based on a thread here where an owner preferred it over Carefree's sewn-edge fabric
- Planning a mobile tech visit to diagnose the mount and handle the fabric R&R together
One wrinkle if it comes to arm replacement: I understand Fixed Flat Pitch arms are now NLA/discontinued per Carefree's own parts list, while Steep Pitch arms are current stock. With 25" of door clearance, I could apparently go to Steep Pitch arms if needed (needs 15.5", Flat needs 7") - but would rather know what I actually have before assuming I need a workaround.
Questions for anyone who's been through this:
- Any way to tell Flat vs Steep pitch without extending the awning? (At this point do I care about further damage from extending the awning?)
- Front mount separation - hardware or substrate, in your experience?
- Anyone had a Travel'r mount issue covered under warranty or recall (found NHTSA 14E065000 / 14E078000 for Carefree Latitude brackets - unclear if related)?
- ShadePro vs. Carefree fabric experience on a Travel'r?
- Fair price range for a mobile tech to do combined mount diagnosis + fabric R&R at this size?
Appreciate any input - trying to make one good decision here rather than a string of small ones.
