GMC Trailer Auxilary Camera Installation for 31G travel trailer?

I swapped the two trailer connectors on the truck, relocating the one at the bumper (that has the camera connectors) to inside the truck bed, and the one in the truck bed to the bumper location. The camera cables were extended to reach the new truck bed location using cables purchased from Amazon.
Thanks!! I’ll have to look into that. You said, “The toughest part was routing the cable from the front bay and to the hitch through the inside of the 5th wheel overhang”. How did you do that? I am still trying to figure out the best way to get to the connection. Right now I just have it fed out the bottom of the left propane bottle bay.
 
Thanks!! I’ll have to look into that. You said, “The toughest part was routing the cable from the front bay and to the hitch through the inside of the 5th wheel overhang”. How did you do that? I am still trying to figure out the best way to get to the connection. Right now I just have it fed out the bottom of the left propane bottle bay.
 
I routed my cable along the bottom of the right hand rail and up through the right propane bay.

The camera connector can be disassembled making it much smaller and easier to deal with by first cutting off the rubber cover over the coax connector then unscrewing the connector with a couple pair of good pliers. The connector has Lock-Tight in the threads so it does not want to easily unscrew therefore some gentle persuasion is required by gently tapping on the connector with a couple of hammers. I want to emphasis gentle because you don't want to crush the connector and repair it (I had to repair mine after pulling it apart during a distracted-by-brother-in-law disconnect incident but that is another story).

I drilled a hole into the front bay behind the propane bottle and routed all the excess cable into the bay. I built a cover out of aluminum to cover the transition hole in the side wall. Next the cable was routed behind the jack and up to the nose of the trailer. I attached the coax connector to a fiberglass fish tape and worked it through the fiberglass insulation to the pin box. Working the cable to the pin box requires patience but it can be done. I tied the cable to the trailer connector using a flexible sleeve I bought on Amazon, and the camera cable is 3 or 4 inches longer than the trailer cable. You will have excess cable, so roll it up and ziptie it behind the front jack.
You can call me at 214-914-3771 if you would like more boring details.
 

Attachments

  • IMG_2764.JPG
    IMG_2764.JPG
    86.4 KB · Views: 11
  • IMG_0970.jpg
    IMG_0970.jpg
    180.5 KB · Views: 12
  • IMG_0971.jpg
    IMG_0971.jpg
    266.4 KB · Views: 11
  • IMG_2765.JPG
    IMG_2765.JPG
    142.9 KB · Views: 11
  • IMG_2765.JPG
    IMG_2765.JPG
    142.9 KB · Views: 12
  • IMG_2766.JPG
    IMG_2766.JPG
    144.9 KB · Views: 11
  • IMG_2767.JPG
    IMG_2767.JPG
    145.7 KB · Views: 12
  • IMG_2768.JPG
    IMG_2768.JPG
    94.7 KB · Views: 18
  • IMG_2769.JPG
    IMG_2769.JPG
    110 KB · Views: 12
I routed my cable along the bottom of the right hand rail and up through the right propane bay.

The camera connector can be disassembled making it much smaller and easier to deal with by first cutting off the rubber cover over the coax connector then unscrewing the connector with a couple pair of good pliers. The connector has Lock-Tight in the threads so it does not want to easily unscrew therefore some gentle persuasion is required by gently tapping on the connector with a couple of hammers. I want to emphasis gentle because you don't want to crush the connector and repair it (I had to repair mine after pulling it apart during a distracted-by-brother-in-law disconnect incident but that is another story).

I drilled a hole into the front bay behind the propane bottle and routed all the excess cable into the bay. I built a cover out of aluminum to cover the transition hole in the side wall. Next the cable was routed behind the jack and up to the nose of the trailer. I attached the coax connector to a fiberglass fish tape and worked it through the fiberglass insulation to the pin box. Working the cable to the pin box requires patience but it can be done. I tied the cable to the trailer connector using a flexible sleeve I bought on Amazon, and the camera cable is 3 or 4 inches longer than the trailer cable. You will have excess cable, so roll it up and ziptie it behind the front jack.
You can call me at 214-914-3771 if you would like more boring details.
Excellent explanation. Thank you very much!! Definitely a better way of running the connection. I really don’t like it down low from the bumper of the truck to the bottom of the trailer.
 

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top Bottom